How do I reset my Whirlpool Duet front load washer?

Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.

Likewise, How do I fix a Whirlpool washer error?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

Also, Do Whirlpool washers have a reset button?

How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

Moreover, How do I reset my Whirlpool washer after a power outage?

How do I reset my Whirlpool washer after a power outage?

1. Unplug the washer for 1 minute from the electrical outlet.
2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. …
3. The motor has now been reset and is ready for you to start a cycle.

How do you reset a front load washer?

How to reset the washing machine:

1. Press POWER to turn the washer off.
2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
4. Plug the washer back in, or turn the circuit breaker back on.

How do I fix E1 error on my Whirlpool washer?

E1 – water inlet alarm

1. Check that the water faucets are not closed.
2. Check that the water pressure in the house is over 20 kPa.
3. Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement.
4. Check that the drain hose is not below 27½” (700 mm) from the floor.

Why is my Whirlpool front load washer not draining?

You need to make sure that the drain hose is not kinked at all. Straighten the hose to make sure that there is enough water flow and that you also remove any blockages from the drainpipe well. Ensure that you are using a U-shaped drain and secure it properly. Your instruction manual will show you how to do this.

Why is my Whirlpool washer not working?

One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.

How can I reset my Whirlpool washer?

To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.

Why is my Whirlpool washer not filling up with water?

If the water inlet valve is defective, the wash may fill slowly or not fill at all. … If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.

How do you reset a washing machine after power outage?

Turn the machine on with dry hands. If it still won’t start, unplug it or turn the circuit breaker off, then back on until the breaker firmly clicks in place and plug the machine into the outlet. Push the restart button. Some machines may require you set the knob to a specific setting for the reset feature to work.

Why is my Whirlpool washing machine not turning on?

One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.

Why is my washing machine not turning on?

Power Source

Make sure the machine is tightly plugged in. Next, check for a tripped circuit breaker. Reset the breaker and try to start the washer. If neither is at fault, you may have a damaged power cord.

Why did my front load washer stop spinning?

Front-load washer tubs spin thanks to a drive belt that runs off of the motor. A loose, frayed, or torn belt could be why your washer won’t spin. Overloading your washing machine can cause the belt to loosen or become worn out. Inspect the drive belt closely.

How do I reset my defy front load washer?

First, you should perform a general reset of the machine. Turn the machine off at the powerpoint, wait for one minute, and then turn it back on. If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians.

Why does my Whirlpool washer not fill with water?

If the water inlet valve is defective, the wash may fill slowly or not fill at all. … If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.

What does E1 error mean on a washing machine?

When the Washing Machine is displaying E1 in the panel, it is indicating an error in the water supply. The appliance is not detecting that the unit is filling with water.

How do I fix error F8 E1?

Error Code F8 E1, LF, or LO FL all indicate that no water is detected entering washer after 13 minutes.
…
Remove F8 E1 Error Code:

1. Unplug the washer or disconnect the power for one minute.
2. Plug in the washer or reconnect the power.
3. Re-select the cycle and press Start.

How do I fix E1 error on my washing machine?

If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.

What do you do when your front load washer won’t drain?

Clogged Drain Hose

Over time, debris can clog the drain hose and prevent your washer from draining. A twisted or coiled drain hose can also inhibit the free flow of water. Check behind the washer and straighten a kinked hose. If this does not solve the problem, unplug and clean the hose to eliminate any residue.

Why is my front loading washer not draining?

A washing machine not draining is one of the most common problems we encounter. It can be caused by one of the following: – The drain hose or pump is clogged with a small item of clothing, residual gunk or other debris. – The washer is malfunctioning and not engaging the drain/spin cycle properly.

How do you run a diagnostic on a Whirlpool Duet washer?

Duet Washer Diagnostic Test Mode

Pick any three buttons on the Duet washer control except power, start, or cancel. Now do the key dance within eight seconds… Button 1, Button 2, Button 3, Button 1, Button 2, Button 3, Button 1, Button 2, Button 3 (You are pressing 9 buttons in 8 seconds so it needs to be pretty quick.)

How do I force my Whirlpool washer to open?

Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.