How do I reset my Whirlpool top load washer?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

Likewise, Why won’t my Cabrio washer fill with water?

Washing Machine Won’t Fill Because Water Inlet Valve Defective. Washing machines have a water inlet valve that allows both hot and cold water into the unit. … No continuity indicates an issue with the valve. When the water inlet valve is the cause for a Whirlpool Cabrio washer not filling with water, it must be replaced.

Also, How do I fix a Whirlpool washer error?

If the Whirlpool washer displays the de error code on display, so there are problems with a door.
…
Manual Review

1. Unplug the Whirlpool washing machine from the mains.
2. Wait for 15-20 minutes while the control unit reboots.
3. Reset the error by pressing the START button (On/Off).
4. Check hatch locking.

Moreover, Why does my Whirlpool washer not turn on?

One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.

How do I reset my top load washer?

Motor Reset Procedure:

1. Unplug the washer for 1 minute from the electrical outlet.
2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
3. The motor has now been reset and is ready for you to start a cycle.

How do I know if my inlet valve is bad?

Signs that point to an inlet valve problem include leaks that fill the dishwasher when not running, the dishwasher filling too slowly when in use, or the dishwasher not filling at all. Leaks that end up outside of the dishwasher also can indicate an inlet valve problem, and this must be addressed immediately.

Why is my Whirlpool washer not holding water?

The most common thing that causes this is that someone taped the drain hose to the drainpipe so that the water will not back out the drain during pump out. The best way to fix this is to clean out the drainpipe so that the water drains freely enough that it doesn’t back out and remove the tape from the drain hose.

Are there any recalls on Whirlpool washers?

Whirlpool has added 21 washing machines to its recall list because of fears they could start a fire. The American home appliance company confirmed that some of its Hotpoint and Indesit models needed to be recalled.

How do you clear a Whirlpool error code?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

What is Fe error in Whirlpool washing machine?

The FE error code indicates that the washer is overfilling. This is usually the result of faulty water valve.

What is E1 error in Whirlpool washing machine?

E1 – water inlet alarm

Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement. Check that the drain hose is not below 27½” (700 mm) from the floor.

How do you fix a Whirlpool dishwasher that won’t start?

If your dishwasher is plugged into an outlet, simply unplug the unit for one minute and then plug the unit back in. If the dishwasher is hard wired to the power supply, turn the breaker off at the home electrical panel that powers the dishwasher for one minute and then turn the breaker back on.

How do you fix a washer that won’t start?

How to Fix a Washing Machine That Won’t Start

1. Activate the power button.
2. Test the outlet.
3. Reset outlet if necessary.
4. Make sure the power cord is plugged in.
5. Check if fuses are blown or the circuit breaker is thrown.
6. See if Delay Start has been pushed.
7. See if Control Lock has been activated.

Does Whirlpool washer have a fuse?

The lid switch is on the top of the washer lid opening. The lid switch needs to be removed from the machine before the two screws that hold it in place can be removed. … The fuse should be located.

Does unplugging a washer reset it?

On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.

Can you reset your washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

Can you clean a water inlet valve?

Washing machines pull in water from your home’s water supply and mix it with detergent in the laundry tub. … It is a good idea to clean the water inlet valve on your washing machine every year or so.

Why is a washer not holding water?

Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed. Whatever the reason, the water will need to be drained from the washing machine before any work or diagnosis can be done.

Why is my washer filling up and draining at the same time?

If your washer continues to fill during a drain cycle, the water inlet valve could be at fault. … If the washer continues to fill, then the inlet valve is defective. If the washer stops filling, then the problem is related to the electrical circuit that controls the valve.

How do I know if my Whirlpool washer has a recall?

Consumers can check if their washing machine is affected by visiting the Whirlpool website. This site includes an online model checker tool, as well as a full list of model numbers.

What models are affected by Whirlpool recall?

Hotpoint and Indesit machines built between 2014 and 2018 are affected, leading consumers to be warned about their safety. Owners of such machines were told to contact Whirlpool directly ahead of the recall and to not use them in the meantime, leaving many unable to wash clothes.

What does F5 mean on a Whirlpool Cabrio washer?

The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.

What does Fe mean on a washing machine?

The FE error code in the LG washing machine is displayed both during the water gaining and in the rinse or washing mode of the laundry. So, with this code, the system signals that the tank of the washing machine is overfilled with water. In particular cases, it means that water has reached the maximum permissible rate.

What does OFb mean on Whirlpool washer?

Your washer is off balance.

If OFb (off balance load) appears in display, the load is out of balance. The washer was unable to remedy the off balance load via automated methods and now needs manual intervention to redistribute the load evenly around the washplate.