How do I run a diagnostic on my GE washer?

Test Mode is initiated by pressing a sequence of buttons on the washer’s control panel.

1. Press the “Power” button on your GE washer. …
2. Unplug the power cord for at least 30 seconds.
3. Plug the power cord back in to the GE washer. …
4. Press “Delay Start” to advance to “t02”.

similarly, How do you troubleshoot a GE washing machine?

How to Troubleshoot a GE Top Load Washer

1. Check the amount of detergent you have put in the washer. …
2. Examine the GE top load washer’s drain hose for leaks. …
3. Check the water connections to your GE top load washer. …
4. Check whether the GE top load washer lid is closing firmly. …
5. Check the load in your GE top loading washer.

on the other hand, Why won’t my GE washer fill?

If your washer won’t fill, check the hot and cold faucets to make sure they’re both turned on fully. … Check the fill hoses, which connect to the upper back left of most GE washers, and make sure the line has no kinks. If the problem persists, turn off the water and remove the fill hoses.

also, Is there a reset button on a washing machine? Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

Why is my GE washer not draining or spinning?

This usually indicates the washer took too long to pump the water out. There may be a clog. Press Start to resume the cycle or you can select Drain & Spin and press Start. If the washer drains properly, then the clog has likely cleared.

Why is my GE washer not starting?

Causes. When a GE washer stops working, it could be because of a broken spin belt, a blown fuse, a melted wire, a backed-up water pipe, or a burnt-out power outlet. The most straightforward reason your GE washer isn’t working anymore is that it’s not plugged into a reliable power source.

Why is my GE washer not filling up?

If your washer won’t fill, check the hot and cold faucets to make sure they’re both turned on fully. … Check the fill hoses, which connect to the upper back left of most GE washers, and make sure the line has no kinks. If the problem persists, turn off the water and remove the fill hoses.

How do I troubleshoot my GE?

How to Troubleshoot a GE Electric Oven

1. Make sure your GE electric oven controls are set for either bake or broil if the oven does not heat, but the burners do heat. …
2. Check the oven knobs and make sure they are in the right position if the device is not producing heat. …
3. Unplug your GE electric oven and check the fuse.

Why does my GE washer keep saying CAnCELEd?

“CAnCELEd” may scroll on the display if the machine was paused for longer than 24 hours or if the machine has stopped itself before the cycle completed due to certain errors. As soon as the message starts to scroll, the washer will initiate a 4 minute lock-out period.

Why is my washer not filling up?

If your washer if not filling, start by making sure the faucet at the water-supply end of the hose is turned on. … If you have un-kinked hoses that are tightly attached and with clean screens, and you have good water pressure, the next place to check for a water-filling problem is the water inlet valve.

What would cause a washer to not fill up?

If your washer doesn’t fill with water, first check that the house water supply to the washer is on. If it is, and the washer won’t fill at all, the inlet valves might have failed. If the washer fills partially, the problem is likely with the temperature selector switch or water-level pressure switch.

How do you reset a GE washer that won’t drain?

How do I reset my GE washer?

1. Unplug the washer for 1 minute from the electrical outlet.
2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
3. The motor has now been reset and is ready for you to start a cycle.

Why is my washing machine not turning on?

Power Source

Make sure the machine is tightly plugged in. Next, check for a tripped circuit breaker. Reset the breaker and try to start the washer. If neither is at fault, you may have a damaged power cord.

How do I fix my washing machine it wont turn on?

How to Fix a Washing Machine that Won’t Start

1. Activate the power button.
2. Test the outlet.
3. Reset outlet if necessary.
4. Make sure the power cord is plugged in.
5. Check if fuses are blown or the circuit breaker is thrown.
6. See if Delay Start has been pushed.
7. See if Control Lock has been activated.

Why is my washer full of water and not spinning?

If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.

What causes a washer not to drain or spin?

Washing machine not draining? If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken. If a washer won’t drain or spin, the fix is simple if you’re even just a little bit handy with tools.

How do you fix a washer that won’t start?

How to Fix a Washing Machine That Won’t Start

1. Activate the power button.
2. Test the outlet.
3. Reset outlet if necessary.
4. Make sure the power cord is plugged in.
5. Check if fuses are blown or the circuit breaker is thrown.
6. See if Delay Start has been pushed.
7. See if Control Lock has been activated.

Why washing machine suddenly stopped working?

If you’re washing machine just suddenly stops working then don’t panic right away it might be easy to fix! Check your power outlets and the fuse, it could be as simple as flicking a switch or changing the fuse.

How do I reset the lid lock on my GE washer?

Top Load Washer – Lid Lock Feature

1. Make sure the washer is paused (press Start/Pause). During spin, this can take up to 3 minutes for the basket to stop spinning and allow you to open the lid.
2. Unplug the washer for a minute to reset.

How do I get my GE washer to fill with water?

There are two ways Deep Fill can be used:

1. Add a little more water: Press the Deep Fill button once before starting the cycle to add 3 gallons of water to the wash load. …
2. Full Tub Fill: Press and hold the Deep Fill button for 3 seconds to fill the washer to the maximum water level.

Does a GE oven have a reset button?

Select the “Clear” button on the built-in GE oven. Switch off the circuit breaker that is controlling the GE built-in oven. Turn the power back on to your GE built-in wall oven.

Where is the thermal fuse on a GE stove?

The thermostat fuse is located near the top middle on the back of the stove. Remove the 2 screws holding it in place. Disconnect the wires, plug in the new part.

How do I reset my deep fill GE washer?

Motor Reset Procedure:

1. Unplug the washer for 1 minute from the electrical outlet.
2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
3. The motor has now been reset and is ready for you to start a cycle.

Don’t forget to share the post !