Unplug your receiver
- Unplug your receiver’s power cord from the electrical outlet, wait 15 seconds, and plug it back in.
- Press the Power button on the front panel of your receiver. Wait for your receiver to reboot.
similarly, How do I fix my DIRECTV remote not working?
Receiver and remote control reset
If the buttons on your remote are not responding, try resetting the receiver and remote control. On most DIRECTV receivers, there is a red button on the side of the receiver or inside the access card door. Press and hold the red button until the receiver restarts.
on the other hand, How do I reset my DIRECTV remote control?
To reset DIRECTV remotes to their default factory settings, press and hold the MUTE and SELECT buttons until the remote’s light flashes three times. Then, enter 981 and press SELECT. The remote will flash four times to let you know it has been reset.
also, Why is my DIRECTV remote not changing the channel? Change the channel using the channel up/down buttons on the receiver. If you can change channels on the receiver, change the batteries in your remote. If you can’t change channels from the receiver, turn it off and unplug it. After at least 15 seconds, plug the receiver back in and turn it on.
Why does my DIRECTV keep losing sound?
Check the audio/video cables
Check that the device connected to the TV and the receiver are powered on. On your remote control, press TV INPUT to cycle through inputs, such as HDMI and HDMI3. If nothing happens, try programming your remote control. If the problem persists, try connecting the receiver to the TV.
Why is my TV not responding to the remote?
A remote control that will not respond or control your TV usually means low batteries. Make sure you are pointing the remote at the TV. There also may be something interfering with the signal such as other electronics, certain types of lighting, or something blocking the TV remote sensor.
Why is my remote not working?
1 Check the Batteries of the Supplied Remote
Low battery power can cause the remote to intermittently function, or not function at all. … Replace the back cover on the remote, and slide down to click it into place. If the remote fails to respond properly after this, replace the existing set of batteries with new ones.
How do I get my directv remote to work?
Press the MENU button on the remote. Go to Settings & Help, then Settings, then Remote Control then Program Remote. Choose the device you want to the remote to control. Follow the on-screen instructions to finish programming your remote.
How do I reprogram my remote?
Turn on your TV or another device you wish to control. Press and hold the corresponding DEVICE and POWER buttons on the remote at the same time. Wait until the power button comes on and then release both buttons. Pointing the remote at the TV or another device, press the Power button on the remote and wait 2 seconds.
Why is my direct tv black?
Problem with Cable connection – Your Directv is most likely to experience a black screen issue due to a cable connection problem. For instance, damaged cables, loose connections, inactive power source. These are some of the possible causes on your TV. … For instance, your DirecTV might be mistakenly set on a wrong input.
Why is my DirecTV cutting in and out?
Check that the cable connection is tight to the box. If there are any adapters connected, check those as well. If you have a SWiM Power Inserter, a small power brick like device that includes two cable connections, unplug it from power for 15 minutes. Make sure nothing is blocking your satellite.
What causes DirecTV to freeze up?
Why Does my DIRECTV Keep Freezing? DIRECTV Keeps Freezing in the following cases: During poor signal quality or weak signal. Overheating issues when the fan is not working or the device is sitting on a soft surface that traps heat, or nearby electronics are producing a lot of heat.
Why will my remote not change channels?
Remote will not change channels or turn on the TV. Batteries are low, dead, or inserted incorrectly. Verify the batteries are inserted in the correct direction. … If the box turns ON or OFF, then install new batteries in the remote and try again.
Why is my remote not working even with new batteries?
The remote control battery terminals may be dirty. Remove the batteries and clean the remote control terminals with a small solution of alcohol, using a cotton bud or soft cloth, then place the batteries back into the remote control. Replace with fresh batteries.
What do you do when your remote won’t change channels?
Remote control won’t change TV channels
- Make sure there are no obstacles between the remote and your TV.
- Move closer to the TV and make sure the remote is pointed directly at the TV’s front panel.
- Make sure the batteries are installed correctly.
- Try fresh batteries.
How do I get my directv remote to turn off my TV?
While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice. Then enter 9911, the green light on remote should flash twice. Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off.
How do I program a directv remote control?
On your remote, press and hold the MUTE and SELECT buttons. Stop when the green light at the top blinks twice. Enter the appropriate manufacturer’s code. If you don’t see your TV or device listed, use the code lookup tool to find the 5-digit code.
How do I fix an unresponsive remote?
Clean the remote control terminals. The remote control battery terminals may be dirty. Remove the batteries and clean the remote control terminals with a small solution of alcohol, using a cotton bud or soft cloth, then place the batteries back into the remote control. Replace with fresh batteries.
Can any TV remote be programmed?
Reprogram your TV remote. You can use electronic remote controls to control just about anything in your entertainment center. However, if you recently purchased a newer television, you need to reset the TV remote so it can be used with the newer television.
How do I fix my black screen on DIRECTV?
Solutions
- Turn TV off and on.
- Turn DIRECTV Receiver off and on.
- Make sure light on front panel of receiver is lit.
- Press the “TV/DSS” button on the remote control or front panel of the receiver (not all receivers have this option).
- Reset the receiver by unplugging the power cord for 15 seconds.
Why is my TV suddenly saying no signal?
First check that your TV is set to the correct Source or Input, try changing the Source or Input to AV, TV, Digital TV or DTV if you haven’t already. If your “No Signal” message is not due to incorrect Source or Input being selected, then it’s most likely caused by a set up or antenna fault.
Why does my TV say no signal when HDMI is plugged in?
Verify that the source device has power and is turned on. If the source device is connected with an HDMI® cable: Make sure the TV and source device are both turned on, then disconnect the HDMI cable from one of the devices and then connect it again. … Try a new or another known working HDMI cable.
What causes a DVR to freeze?
The most common things that cause a freezing event are the incorrect distance between the DVR and CCTV cameras, a faulty power point, other wireless devices are interfering with your DVR, and the hard drive might be corrupted.
Don’t forget to share the post !