How to Troubleshoot a GE Top Load Washer
Table of Contents
READ ALSO
- Check the amount of detergent you have put in the washer. …
- Examine the GE top load washer’s drain hose for leaks. …
- Check the water connections to your GE top load washer. …
- Check whether the GE top load washer lid is closing firmly. …
- Check the load in your GE top loading washer.
similarly, Why isn’t my GE washer working?
A loss of electrical power to the washer will cause a failure to spin. To check for power at the outlet, carefully plug a small table lamp or hair dryer into the wall outlet and turn it on. If it does not work, you may have blown a fuse, tripped a circuit breaker or have a defective wall outlet.
on the other hand, Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
also, Why is my washer not agitating? If your washer won’t agitate but spins, a broken agitator may be to blame. … The output shaft of the transmission is splined to the agitator to secure it in place. Over time, some of the components of the agitator can wear down or break with normal usage, causing your washing machine not agitating issue.
How long should a GE washer last?
A washer can last between 12 and 14 years, while a dryer lasts between 18 and 24 years. The washer and dryer should last a long time.
How do you force a GE washer to drain?
There may be a clog.
- Press Start to resume the cycle or you can select Drain & Spin and press Start. …
- If water remains in the washer, check for a pinched or flattened drain hose. …
- If you clear a clog, press START to resume your cycle or you can select Drain & Spin and press Start.
How do you fix a washer that won’t drain?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
How do you reset a GE washer that won’t drain?
How do I reset my GE washer?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
- The motor has now been reset and is ready for you to start a cycle.
How do you clear the error code on a GE washing machine?
How to Access Error Codes on GE Washers
- Press the “Power” button on your GE washer. …
- Unplug the power cord for at least 30 seconds.
- Plug the power cord back in to the GE washer. …
- Press “Delay Start” to advance to “t02”. …
- Press and hold “Start/Pause” to clear the saved error codes after viewing them.
Why is my GE washer not draining or spinning?
This usually indicates the washer took too long to pump the water out. There may be a clog. Press Start to resume the cycle or you can select Drain & Spin and press Start. If the washer drains properly, then the clog has likely cleared.
How do you fix a GE washer that won’t agitate or spin?
Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. The motor coupling connects the motor to the washer transmission.
Is it worth repairing a 15 year old washing machine?
As a general rule, if it costs less than 50% of the price of a new washing machine to repair your old one, you should choose the repair option. But, you should also consider whether or not there is a warranty coverage on your washer and think about economic realities.
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.
How often should you replace your washing machine?
Washing machines, on average, last around 10 years, according to Consumer Reports. If your washer is reaching the threshold, or it’s been having some problems, here are some signs the end may be near.
How do I know if my washing machine drain pump is bad?
You can check by looking for a few signs that a pump is dying or already dead.
- Start the washer and wait for the washer tub to fill with water. If you do not hear water or hear a motor whirring, the washer motor may be dead.
- Open the washer lid in mid-cycle. …
- Wait for the washer to finish its cycle.
Why is my washer not draining or spinning?
Washing machine not draining? If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken. If a washer won’t drain or spin, the fix is simple if you’re even just a little bit handy with tools.
Why is my GE washer not spinning or agitating?
Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. If the lid switch assembly fails, the washer will not spin. …
What would cause a washer not to drain?
There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
What causes a washing machine not to drain and spin?
Washing machine not draining? If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken. If a washer won’t drain or spin, the fix is simple if you’re even just a little bit handy with tools.
How do I know if my washing machine drain pump is bad?
You can check by looking for a few signs that a pump is dying or already dead.
- Start the washer and wait for the washer tub to fill with water. If you do not hear water or hear a motor whirring, the washer motor may be dead.
- Open the washer lid in mid-cycle.
- Wait for the washer to finish its cycle.
Why is my washer full of water and not spinning?
If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.
Why are my clothes too wet after the spin cycle?
Loading Too Many Items
Overloading can lead to an imbalance that reduces the washer’s spin speed, leaving clothes too wet after spin cycle completes. If the washer leaves clothes soaked after a large load, remove some items, redistribute others and run another rinse and spin cycle.
How do I get my washing machine to drain?
If not, follow these steps:
- Step 1: Turn off the power and lay down towels.
- Step 2: Locate the drain hose at the back of the washing machine.
- Step 3: Drain the water.
- Step 1: Turn off the power and lay down towels.
- Step 2: Locate the drain hose.
- Step 3: Drain the water.
- Step 4: Scrub the filter.
Don’t forget to share the post !
