How to Troubleshoot a GE Top Load Washer
- Check the amount of detergent you have put in the washer. …
- Examine the GE top load washer’s drain hose for leaks. …
- Check the water connections to your GE top load washer. …
- Check whether the GE top load washer lid is closing firmly. …
- Check the load in your GE top loading washer.
similarly, Do washers have a reset button?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
on the other hand, Why won’t my GE washer fill all the way up?
If your washer won’t fill, check the hot and cold faucets to make sure they’re both turned on fully. … Check the fill hoses, which connect to the upper back left of most GE washers, and make sure the line has no kinks. If the problem persists, turn off the water and remove the fill hoses.
also, Why is my GE washer not draining or spinning? This usually indicates the washer took too long to pump the water out. There may be a clog. Press Start to resume the cycle or you can select Drain & Spin and press Start. If the washer drains properly, then the clog has likely cleared.
Do GE washing machines have fuses?
GE washer fuse or circuit Breaker washer, is located behind the control panel.!
Why did my washer just stopped working?
There are a number of possible causes for your washing machine not working as it should. … Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining.
How do I reset the lid lock on my GE washer?
Top Load Washer – Lid Lock Feature
- Make sure the washer is paused (press Start/Pause). During spin, this can take up to 3 minutes for the basket to stop spinning and allow you to open the lid.
- Unplug the washer for a minute to reset.
Why is my GE washer not filling up with water?
If your washer won’t fill, check the hot and cold faucets to make sure they’re both turned on fully. … Check the fill hoses, which connect to the upper back left of most GE washers, and make sure the line has no kinks. If the problem persists, turn off the water and remove the fill hoses.
Why wont my washing machine fill all the way up?
If your washer doesn’t fill with water, first check that the house water supply to the washer is on. If it is, and the washer won’t fill at all, the inlet valves might have failed. If the washer fills partially, the problem is likely with the temperature selector switch or water-level pressure switch.
How do you reset a GE washer that won’t drain?
How do I reset my GE washer?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
- The motor has now been reset and is ready for you to start a cycle.
Why is my washer full of water and not spinning?
If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.
How do you fix a GE washer that won’t drain?
If the washer won’t drain or is not draining properly, and the washer has a coin trap, remove the coin trap and clean it thoroughly. First, check the drain hose to determine if it is kinked, twisted, or bent. If the drain hose is bent, straighten it out. In addition, remove the drain hose and check it for obstructions.
What would cause a washer to stop working?
Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.
How do you fix a washer that won’t turn on?
How to Fix a Washing Machine that Won’t Start
- Activate the power button.
- Test the outlet.
- Reset outlet if necessary.
- Make sure the power cord is plugged in.
- Check if fuses are blown or the circuit breaker is thrown.
- See if Delay Start has been pushed.
- See if Control Lock has been activated.
Is there a fuse in a washing machine?
Washing machines have fuses that protect them from power surges. Washing machines require lots of power to run. … The other fuse sits in the lid switch on some machines; if the washer overheats or there is a power surge, the washer will not run again until the fuse in the switch is replaced.
How do you fix a washer that won’t start?
How to Fix a Washing Machine That Won’t Start
- Activate the power button.
- Test the outlet.
- Reset outlet if necessary.
- Make sure the power cord is plugged in.
- Check if fuses are blown or the circuit breaker is thrown.
- See if Delay Start has been pushed.
- See if Control Lock has been activated.
What to do if washer fills with water then stops?
If your washing machine fills with water but fails to advance through the cycle with a closed lid, remove and replace the lid switch. Open your washing machine lid and look for the two screws above the switch opening next to the washtub opening. Tighten the two screws and lower the washer lid.
Do GE washers have a reset button?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
Can you bypass a lid lock on a GE washer?
Most washing machines come equipped with a lid switch. … This switch performs the same function, but the lid must be locked in place for the machine to wash. A simple bypass for the first type of lid switch is to simply jam a piece of wood into the switch, causing it to activate the solenoid.
How do I get my GE washer to fill with water?
There are two ways Deep Fill can be used:
- Add a little more water: Press the Deep Fill button once before starting the cycle to add 3 gallons of water to the wash load. …
- Full Tub Fill: Press and hold the Deep Fill button for 3 seconds to fill the washer to the maximum water level.
Why is my washing machine not holding water?
Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed. Whatever the reason, the water will need to be drained from the washing machine before any work or diagnosis can be done.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do I know if my inlet valve is bad?
Signs that point to an inlet valve problem include leaks that fill the dishwasher when not running, the dishwasher filling too slowly when in use, or the dishwasher not filling at all. Leaks that end up outside of the dishwasher also can indicate an inlet valve problem, and this must be addressed immediately.
Don’t forget to share the post !