Use an ohmmeter to determine whether the pressure switch is malfunctioning.
- Unplug the Whirlpool Duet washer power cord from the wall outlet. …
- Go behind the Duet and remove the three screws securing the top panel to the rear panel with a Phillips-head screwdriver. …
- Locate the pressure switch inside the washer cabinet.
similarly, How do I reset my Whirlpool Duet washer?
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.
on the other hand, How do you run a diagnostic on a Whirlpool Duet washer?
Duet Washer Diagnostic Test Mode
Pick any three buttons on the Duet washer control except power, start, or cancel. Now do the key dance within eight seconds… Button 1, Button 2, Button 3, Button 1, Button 2, Button 3, Button 1, Button 2, Button 3 (You are pressing 9 buttons in 8 seconds so it needs to be pretty quick.)
also, Is there a reset button on a Whirlpool front load washer? How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I reset my Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
How do you clear the error code on a Whirlpool front load washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Where do I find the error code on a Whirlpool Duet washer?
Duet Washer Error / Fault Codes. Once you are in the Duet Washer’s Diagnostic Mode momentarily press the 3rd button you used to enter diagnostics, and the washer will display the last 4 fault codes one button press at a time.
Why is my Whirlpool washing machine not turning on?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do you unlock a Whirlpool front load washer?
Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.
How do I fix a Whirlpool washer error?
If the Whirlpool washer displays the de error code on display, so there are problems with a door.
…
Manual Review
- Unplug the Whirlpool washing machine from the mains.
- Wait for 15-20 minutes while the control unit reboots.
- Reset the error by pressing the START button (On/Off).
- Check hatch locking.
How do I reset my Whirlpool washer after a power outage?
How do I reset my Whirlpool washer after a power outage?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. …
- The motor has now been reset and is ready for you to start a cycle.
What does F1 mean on a Whirlpool Duet washer?
When the Whirlpool washing machine displays an F1 error code, this usually means that the control board is having difficulty communicating with the motor.
Why does my Whirlpool washer not start?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
Why does my Whirlpool washer says low detergent?
Detergent Level Low – This will light (yellow) if there is enough detergent in the Load & Go™ cartridge for only a few more cycles. Empty – This will light (red) if there is no detergent in the Load & Go™ cartridge.
What do you do when your washing machine won’t turn on?
How to Fix a Washing Machine That Won’t Start
- Activate the power button.
- Test the outlet.
- Reset outlet if necessary.
- Make sure the power cord is plugged in.
- Check if fuses are blown or the circuit breaker is thrown.
- See if Delay Start has been pushed.
- See if Control Lock has been activated.
Why is my washing machine not turning on?
Power Source
Make sure the machine is tightly plugged in. Next, check for a tripped circuit breaker. Reset the breaker and try to start the washer. If neither is at fault, you may have a damaged power cord.
What is the problem with Whirlpool washing machines?
The machines, branded as Hotpoint or Indesit, were sold for more than five years, but their door locking system can overheat creating the risk of fire. Owners face the prospect of doing without hot washes for months until products are fixed or replaced.
Why does my Whirlpool washer not fill with water?
If the water inlet valve is defective, the wash may fill slowly or not fill at all. … If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.
How do you unlock the control lock on a Whirlpool Duet washer?
How to Unlock the Controls for a Whirlpool Duet Washer
- Locate the “Control Lock/Unlock” button on your Duet’s control panel.
- Press and hold the “Control Lock/Unlock” button for three seconds.
- Release the “Control Lock/Unlock” button when the control lock icon on the display disappears.
How do I unlock my front load washer door?
Opening a Manual Lock. Turn the washing machine off and unplug it. If you’re in the middle of a cycle, turn the dial or press the button to pause or end the cycle. Wait 5-6 seconds to see if the door unlocks.
How do you unlock a Whirlpool front load washer?
Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.
What is E1 error in Whirlpool washing machine?
E1 – water inlet alarm
Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement. Check that the drain hose is not below 27½” (700 mm) from the floor.
How do I reset my whirlpool?
To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.
Don’t forget to share the post !