To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Table of Contents
READ ALSO
Likewise, How do I fix error code F21 on Maytag?
Problem with the overflow contact.
- Disconnect power to the washer.
- Turn off both hot and cold water faucets.
- Make sure the drain hose is free from kinks and obstructions.
- Clean the drain pump filter.
- Plugin the washer.
- Try to restart the machine.
Also, Do Whirlpool washers have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
Moreover, How do I reset my Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
How do you reset error F21?
Reset. When the “F21” error code appears, try pressing “Pause/Cancel” to stop the current wash cycle. If water remains in the washing machine tub, touch “Drain/Spin” to force a secondary drain cycle to remove the water. Once all the water drains, try selecting a new wash cycle and pushing “Start.”
How do I clear the error code on my Maytag front load washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I reset my Maytag front load washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
How do I fix a Whirlpool washer error?
If the Whirlpool washer displays the de error code on display, so there are problems with a door.
…
Manual Review
- Unplug the Whirlpool washing machine from the mains.
- Wait for 15-20 minutes while the control unit reboots.
- Reset the error by pressing the START button (On/Off).
- Check hatch locking.
How do you reset a Whirlpool washer?
To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.
Why is my Whirlpool front load washer not draining?
You need to make sure that the drain hose is not kinked at all. Straighten the hose to make sure that there is enough water flow and that you also remove any blockages from the drainpipe well. Ensure that you are using a U-shaped drain and secure it properly. Your instruction manual will show you how to do this.
How do I reset my front load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do you run a diagnostic on a Whirlpool Duet washer?
Duet Washer Diagnostic Test Mode
Pick any three buttons on the Duet washer control except power, start, or cancel. Now do the key dance within eight seconds… Button 1, Button 2, Button 3, Button 1, Button 2, Button 3, Button 1, Button 2, Button 3 (You are pressing 9 buttons in 8 seconds so it needs to be pretty quick.)
What does E1 F9 mean on a Whirlpool washer?
F9 E1 Code in the display:
This error code indicates that drain times are longer than expected, typically over eight (8) minutes.
What does F mean on my Maytag washer?
Maytag F/02 – Drain Cycle Too Long
The manufacturer has assigned this error or fault code to indicate that the washing machine drain cycle is taking too long. After 8 minutes of drain time the error code is displayed. … If the error code returns, check to be sure the drain hose isn’t clogged or kinked.
Is there a recall on Maytag washers?
Important: CPSC Recall Remedy Notice Due to COVID-19
Description: The recall involves white Maytag front-load washers with model number MAH9700 and a serial number from 10188468GA through 11683946GJ. The model and serial numbers are located inside the door opening and below the rubber boot.
How do you reset a front load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do you manually unlock a front load washer?
Possible Solutions
- Turn off and unplug the washer/dryer.
- Close the water faucet.
- Wait until the drum has stopped rotating – never open the door while the drum is in motion.
- Wait until water and laundry have cooled down when washing with high temperatures.
Is there a way to reset a Maytag washer?
Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.
What is E1 error in Whirlpool washing machine?
E1 – water inlet alarm
Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement. Check that the drain hose is not below 27½” (700 mm) from the floor.
What is Fe error in Whirlpool washing machine?
The FE error code indicates that the washer is overfilling. This is usually the result of faulty water valve.
What does De error mean on Whirlpool washer?
The DE combination of the display of your Whirlpool washing appliance signalizes that there is a problem with the hatch door. In other words, the door of your device can not be closed or locked properly. … The door can not be opened after the washing cycle is completed.
Why is my Whirlpool washer not working?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
