What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
Likewise, How do you fix a washer that won’t start?
How to Fix a Washing Machine That Won’t Start
- Activate the power button.
- Test the outlet.
- Reset outlet if necessary.
- Make sure the power cord is plugged in.
- Check if fuses are blown or the circuit breaker is thrown.
- See if Delay Start has been pushed.
- See if Control Lock has been activated.
Also, What causes washer to not drain?
There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
Moreover, What causes a washer to not spin out all the water?
If your washer will not spin out all water and clothes are still wet, the drain pump might be clogged with debris or possibly faulty. There could be a foreign object that is stuck in the pump and inside the drain hose. Check these areas and remove anything that may be clogging the draining system on your washer.
Why is my washing machine drain backing up?
A clogged drain causes water to back up into the standpipe and spill on the floor. Clearing the clogged drain will usually resolve the problem. … The clog could either be in this trap area, or it could be further down the drain line. To determine where the clog is located, first, fill the washing machine with water.
Why washing machine suddenly stopped working?
If you’re washing machine just suddenly stops working then don’t panic right away it might be easy to fix! Check your power outlets and the fuse, it could be as simple as flicking a switch or changing the fuse.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
What would cause a washer to stop working?
Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.
How often should you drain your washing machine?
Washing machines can be breeding grounds for salmonella and other germs. When you wash items in hot water, your machine is being cleaned as well, but once a month, you should still run an empty load with hot water and about a cup of distilled white vinegar to sanitize the basin and wipe out any lingering germs.
How do I know if my washing machine drain pump is bad?
You can check by looking for a few signs that a pump is dying or already dead.
- Start the washer and wait for the washer tub to fill with water. If you do not hear water or hear a motor whirring, the washer motor may be dead.
- Open the washer lid in mid-cycle. …
- Wait for the washer to finish its cycle.
How do you unblock a washing machine drain?
To unclog a clogged drain, first fill a bucket with boiling water and a pack of baking soda. Remove the drain pipe from your washing machine and slowly pour the water into the drain using a funnel. Wait a few minutes and test if it keeps draining if you pour water into it.
What do you do if your washer is soaking wet?
If the washer leaves clothes soaked after a large load, remove some items, redistribute others and run another rinse and spin cycle. This will create a more balanced load and enable proper spin cycle speed. Avoid overloading by only filling the washer ¾ of the way full with each wash load.
Do I need to spin my washing machine twice?
Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component.
How long should a washing machine last?
Newer washing machines are more efficient than older models. Washing machines, on average, last around 10 years, according to Consumer Reports. If your washer is reaching the threshold, or it’s been having some problems, here are some signs the end may be near.
How do I know if my washing machine drain is clogged?
Observe the washing machine as it pumps water into the hoses and up into the standpipe. If you see water back up and out of the standpipe, your washer’s drain is most likely the issue. The amount of time it takes for the standpipe to fill up and overflow helps you diagnose where the clog is located.
How do you unblock a washing machine drain pipe?
To unclog a clogged drain, first fill a bucket with boiling water and a pack of baking soda. Remove the drain pipe from your washing machine and slowly pour the water into the drain using a funnel. Wait a few minutes and test if it keeps draining if you pour water into it.
How do I know if my washer drain if clogged?
Test the drain by pouring water into it, if it has been backing up. If it’s clogged, you should be able to clear the clog with a plumbing auger.
How do I know if my washing machine is broken?
6 signs it’s time to replace your washing machine
- The drum won’t spin at the end of the cycle. …
- The machine still works but the water hasn’t drained. …
- It’s more noisy than it should be. …
- You don’t trust it with your clothes. …
- It’s no longer big enough for your family. …
- It’s much older than your latest smartphone.
How often should you replace a washing machine?
The average life expectancy of a new washing machine is 11 years. Consumer Reports recommends replacing any appliance that’s more than eight years old, unless it’s a high-end model and has a particular appeal to you.
How long should a washer last?
How long does a washing machine last? A typical washer should last 10-13 years. Top-loading washers typically last a few years longer than their front-loading brethren. If you use a stacked washer/dryer combo, you may have to replace both if one starts acting up.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Why is washer not draining water?
There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.