A Whirlpool refrigerator not cooling may have a dirty or damaged gasket that leaks cold air, warming the refrigerator’s interior. Inspect the door gasket for damage, using a cloth dipped in warm water to clean away any dirt and debris. If the gasket is ripped or broken it will need to be professionally replaced.
Likewise, What do I do if my Whirlpool refrigerator is not cooling?
Check the condenser coils to determine if they are dirty—if the condenser coils are dirty, clean them. The condenser fan motor draws air though the condenser coils and over the compressor. If the condenser fan motor is not working properly, the refrigerator won’t cool properly.
Also, Why is my refrigerator running but not cooling?
Clogged coils can cause poor cooling. Check to make sure nothing is stuck in the condenser fan and that it spins freely (models with coils on the back won’t have a fan). To do this, unplug the fridge and pull it out. … Plug in the fridge and make sure the fan runs when the compressor is running.
Moreover, Is there a reset button on a Whirlpool refrigerator?
Press the door switches and the refrigerator temperature button three times within 10 seconds. After releasing the switches, there should be a letter “S” display in the freezer section and an “E” in the refrigerator’s display.
What would cause a refrigerator to stop getting cold?
As the refrigerant travels through the coils at a high pressure, it cools and turns back into a liquid. Clogged condenser coils can produce poor circulation of air, restricting your fridge’s ability to keep cool.
Why would a refrigerator stop cooling?
Problem: Fridge Not Cooling
Be sure the fridge is plugged in and getting power. … Vacuum the coils under or behind the fridge. Clogged coils can cause poor cooling. Check to make sure nothing is stuck in the condenser fan and that it spins freely (models with coils on the back won’t have a fan).
What is the first thing to check when a refrigerator stops working?
The first thing to check is the breaker (in your home’s electrical service panel) of the circuit serving the fridge.
What to do if refrigerator is not cooling?
Depending on what’s causing your fridge not to keep perishable foods cold enough, the following procedures might help.
- Make sure your fridge is getting power.
- Check the refrigerator’s thermostat.
- Test the seals on your fridge doors.
- Determine whether the refrigerator is level.
- Clean the condenser coils.
How do I run a diagnostic on my Whirlpool refrigerator?
Starting Diagnostics
To start with we need to start the refrigerator’s diagnostic mode. To do this open the refrigerator door and press one or both door switches, depending on your refrigerator type. Next press the refrigerator temperature (+) button three times in ten seconds and release the light switch or switches.
How do I reset my Whirlpool refrigerator compressor?
How to Reset the Compressor on a Fridge
- Locate the refrigerator power cord on the back of the appliance.
- Disconnect the power cord from the wall outlet. …
- Turn both the fridge and freezer controls to “Off” or “0” inside the fridge. …
- Adjust the fridge and freezer controls to the desired setting.
What to do if fridge is not cooling?
Depending on what’s causing your fridge not to keep perishable foods cold enough, the following procedures might help.
- Make sure your fridge is getting power.
- Check the refrigerator’s thermostat.
- Test the seals on your fridge doors.
- Determine whether the refrigerator is level.
- Clean the condenser coils.
How much does it cost to fix a refrigerator that is not cooling?
Some repairs that are generally worthwhile include cleaning a dirty coil, unclogging a drain line, or replacing a faulty thermostat. A fridge that won’t stay cold is usually suffering from a bad thermostat or a dirty coil. Both of these problems can be fixed in about an hour, and will cost about $50 to $250.
Why is my Whirlpool fridge freezing everything?
Temperature Settings
The optimum temperature range for storing fresh food is between 38 – 40 degrees Fahrenheit. If your food is freezing, then it is possible that your fridge’s temperature setting was accidentally set too low. This is a common problem that can lead to your refrigerator freezing food.
What happens when refrigerator condenser fan fails?
If your condenser fan stops, the temperature of the refrigerant will rise and the compressor may overheat. … The fan runs whenever the compressor runs, and it draws cool room air through the front grille, and circulates it through the condenser coils, over the compressor, and back out the front grille into the room.
How do you diagnose a refrigerator problem?
- Check the temperature setting.
- Assure that there is enough room for air flow in the refrigerator or freezer.
- Check for air flow restrictions in vents.
- Test the temperature control.
- Clean the condensor coils.
- Check the door seals.
- Test the door switch.
- Test the defrost heater.
What can damage a refrigerator?
6 Habits That Can Cause Refrigerator Damage
- Overstocking/Understocking Causing Refrigerator Damage. …
- Forgetting to Clean the Coils. …
- Storing Leftovers Improperly. …
- Placing Your Fridge Too Close to the Wall. …
- Leaving the Door Open Too Long. …
- Not Checking the Drainage Hole.
Is it cheaper to repair or replace a refrigerator?
replace. Built-in refrigerators are almost always worth repairing. Not only are they less expensive to repair but typically have a longer lifespan anyways. Side-by-side refrigerators should be repaired within a five-year window and considered for replacement after that.
Why is my fridge warm?
Your refrigerator stays at the proper temperature thanks to cold air that’s consistently circulated through the appliance. If there are too many items in your fresh food compartment, that cold air may not circulate properly, resulting in a refrigerator that’s warm.
How do I program my Whirlpool refrigerator?
Programming Mode (Version 2):
- Press and hold the WATER Keypad.
- Press and hold LL Keypad.
- Release the WATER Keypad and wait 3 seconds.
- The control will display PE to indicate the programming mode.
- Entry is confirmed by pressing the LL Keypad once more.
- The control will display the current Program CODE.
How do you turn on a Whirlpool Gold refrigerator?
-The On/Off switch, located on the left wall of the freezer door, can only be accessed when the ice storage bin has been removed. -To turn on the ice maker, flip the switch to the ON (up) position.
How do you tell if the compressor is bad on a refrigerator?
The best way to tell if something has gone wrong with the compressor is to pull the fridge slightly out from the wall and listen closely. If the motor is running with a slight humming sound but the temperature is above what its normal range should be, then it’s likely there could be a problem with the compressor.
How do I know if my thermostat is bad in my refrigerator?
Here are some signs that your fridge has a faulty thermostat and some troubleshooting tips to help you deal with them.
- The Refrigerator Is Not Cool Enough.
- Unusually Cold Refrigerator.
- Refrigerator Temperature Fluctuation.
- Sub-Zero Refrigerator Temperature Troubleshooting Tips.
- Contact Wilshire Refrigeration.
How do I know if my refrigerator compressor is not working?
The best way to tell if something has gone wrong with the compressor is to pull the fridge slightly out from the wall and listen closely. If the motor is running with a slight humming sound but the temperature is above what its normal range should be, then it’s likely there could be a problem with the compressor.
What happens when a refrigerator fan stops working?
If the fan stops, the temperature of the refrigerant will rise and the compressor may overheat. Eventually, the food may spoil. To check the condenser fan motor, first unplug the refrigerator and pull it away from the wall. … If the motor binds or doesn’t move at all, replace it.
