What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
similarly, Why is the spin cycle not working?
An unbalanced load of laundry is one of the most common causes of an inadequate spin cycle. Sometimes clothing can settle on one side of the drum, throwing off the motion of the washing machine. … If you suspect a distribution problem, try rearranging your clumped-up wet laundry and running the spin cycle again.
on the other hand, Why does my Whirlpool washer not start?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
also, What would cause my Whirlpool washer to not drain? If your washer’s drain hose is kinked or bent, the washer will not be able to drain properly. The drain hose may also be obstructed by a small article of clothing. Check your drain hose and remove any obstructions, and straighten it if it’s bent. Make sure the hose is placed less than eight feet above the floor.
Why is my washing machine not turning on?
Power Source
Make sure the machine is tightly plugged in. Next, check for a tripped circuit breaker. Reset the breaker and try to start the washer. If neither is at fault, you may have a damaged power cord.
Why isn’t my front load washer spinning?
Front-load washer tubs spin thanks to a drive belt that runs off of the motor. A loose, frayed, or torn belt could be why your washer won’t spin. Overloading your washing machine can cause the belt to loosen or become worn out. Inspect the drive belt closely.
Why is my washer not starting?
You should check the outlet to make sure it’s working. Then, check if a fuse is blown or a circuit breaker thrown. If those both work, see if the Delay Start button or Control Lock feature has been activated. Sometimes it’s as simple as opening and closing the door to reset the washer.
Does a Whirlpool washer have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
Why is there no power to my washing machine?
If you are stuck facing an appliance with no power check your home’s fuse box, if something is going wrong the washer will blow the fuse or trip the electrics, replacing the fuse or resetting the trip should bring power back to your appliance.
How do I force my Whirlpool washer to drain?
Find the “Pause/Cancel” button on the control panel. Press this button twice to drain the washer. Press the “Power” button and rotate the cycle selection knob to “Drain and Spin” to remove the remaining water from the load. Check the washer’s discharge hose if the water fails to drain from the washtub.
Why is my front load washer not draining completely?
Clogged Drain Hose
Over time, debris can clog the drain hose and prevent your washer from draining. A twisted or coiled drain hose can also inhibit the free flow of water. Check behind the washer and straighten a kinked hose. If this does not solve the problem, unplug and clean the hose to eliminate any residue.
How do I know if my washing machine drain pump is bad?
How do I know if my washing machine water pump is bad?
- Start the washer and wait for the washer tub to fill with water. If you do not hear water or hear a motor whirring, the washer motor may be dead.
- Open the washer lid in mid-cycle.
- Wait for the washer to finish its cycle.
Why is my Whirlpool front load washer not turning on?
Display board: If you find your Whirlpool washing machine start button not working, the display panel may be defective. If some buttons work but others don’t, the panel must be replaced. … Once it blows, power to the washer is cut off and won’t resume until the fuse is replaced.
Why does my Whirlpool washer not turn on?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
Why is my Maytag washer not starting?
If your Maytag washing machine isn’t starting, verify that the power cord is connected to a live outlet. Test the outlet with another three-prong appliance. … Select a wash setting and pull out the knob to start the cycle. If it still won’t start, reset the circuit breaker or change out the fuses if they are blown.
How do you reset a Whirlpool washing machine?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
What’s wrong when washer won’t spin?
If your washer fills with water but doesn’t agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. (Note: Direct-drive washing machines do not have belts.)
Why is my Whirlpool washing machine not starting?
First ensure that power is getting to the electrical outlet. If the electrical outlet is receiving power, but the washer won’t start, the power cord might be defective. … To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.
Why is my Maytag washer not turning on?
Check to see if your Maytag washer has blown a fuse if the washer is on a fuse box. You might have to replace it or call an electrician if the problem continues. … If the outlet is receiving power to turn the appliance on, but the Maytag washer still will not power on, it can be an issue with a defective power cord.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How do you reset a Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Why does my Maytag washer have no power?
Check to see if a household circuit breaker or Ground Fault Circuit Interrupter (GFCI) outlet has tripped. If so, reset the circuit breaker or Ground Fault Circuit Interrupter. If the washer is on a fuse box, check to see if a fuse has blown and replaced it, if necessary.
How do I unlock my Whirlpool washer without power?
Press the “Drain and Spin” button on the washer’s control panel to attempt to unlock the machine. This may drain any excess water that could cause the machine to remain locked. Once the “Drain and Spin” cycle completes, the door should unlock.
Don’t forget to share the post !