How do you fix a Whirlpool washer that won’t start?

Troubleshooting When Your Whirlpool Front Load Washer Won’t Start

1. Washer is unplugged: Make sure the power cord is plugged in to a functioning outlet.
2. Tripped circuit breaker: Check for tripped breakers in your home’s circuit breaker box, resetting any as needed.

Likewise, Why is my Maytag washer not starting?

If your Maytag washing machine isn’t starting, verify that the power cord is connected to a live outlet. Test the outlet with another three-prong appliance. … Select a wash setting and pull out the knob to start the cycle. If it still won’t start, reset the circuit breaker or change out the fuses if they are blown.

Also, Why won’t my Whirlpool washer fill with water?

If the water inlet valve is defective, the wash may fill slowly or not fill at all. … If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.

Moreover, Where is the reset button on a Maytag washer?

How to Reset a Maytag Washer

1. Press the “Power/Cancel” button.
2. Push the appropriate button to choose a new cycle.
3. Press “Start/Pause.” You have now reset your Maytag washer.

Why does my washer have no power?

No power issues are typically caused by a tripped circuit breaker, a faulty electrical outlet, a power outage in the home, or in rare cases a unit that requires a repair.

What is the problem with Whirlpool washing machines?

The machines, branded as Hotpoint or Indesit, were sold for more than five years, but their door locking system can overheat creating the risk of fire. Owners face the prospect of doing without hot washes for months until products are fixed or replaced.

How do you reset the error code on a Maytag washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do I reset my washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

How do you reset a Maytag?

Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

Where is the fuse on my Whirlpool washing machine?

The lid switch is on the top of the washer lid opening. Plug the washing machine in. The lid switch needs to be removed from the machine before the two screws that hold it in place can be removed. The fuse should be located.

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

Are there any recalls on Whirlpool washers?

Whirlpool has added 21 washing machines to its recall list because of fears they could start a fire. The American home appliance company confirmed that some of its Hotpoint and Indesit models needed to be recalled.

How do I clear the error code on my Whirlpool washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

Why is my Maytag washer stuck on wash cycle?

Maytag washer keeps spinning for various reasons like a faulty driver belt, defective motor control board, and a worn-out clutch band kit. Your washer might be stuck in the spin or rinse cycle when you use excess power detergent, timer issues, drain control issues, and electrical problems.

How do you reset a front load washer?

How to reset the washing machine:

1. Press POWER to turn the washer off.
2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
4. Plug the washer back in, or turn the circuit breaker back on.

How do you bypass the clean cycle on a Maytag washer?

Hello Sandy, Press and hold the “Spin” and “Soil” button simultaneously for 10 seconds. A countdown will be displayed on the console. Once the countdown has completed the unit will have successfully reset.

Does unplugging a washer reset it?

On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.

How do I know if my washing machine control board is bad?

A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.

How long do Whirlpool washers last?

A washer can last between 12 and 14 years, while a dryer lasts between 18 and 24 years. The washer and dryer should last a long time.

How do I know if my Whirlpool washer has a recall?

Consumers can check if their washing machine is affected by visiting the Whirlpool website. This site includes an online model checker tool, as well as a full list of model numbers.

What is the warranty on Whirlpool washing machines?

Most Whirlpool appliances come with one-year warranties that cover the necessary replacement parts and labor to correct breakdowns or failures that result from defective materials or workmanship. Whirlpool also offers extended service plans for your range, dishwasher, refrigerator, washer, and dryer.

What is E1 error in Whirlpool washing machine?

E1 – water inlet alarm

Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement. Check that the drain hose is not below 27½” (700 mm) from the floor.

How do you unlock a Whirlpool front load washer?

Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.