In the Settings menu, find Backup & reset, then tap Factory data reset and Reset phone. You’ll be prompted to enter your passcode and then to Erase everything.
Table of Contents
READ ALSO
Likewise, How do I fix the HC error on my Samsung dryer?
Heating errors (HC, hE, HC4, 1 HC)
This means that the dryer is getting too hot. The most common cause is a clogged lint screen or vent system trapping heat in the dryer. Clean the lint screen, vent system, or both to correct the error.
Also, Where is the dryer reset button?
Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes.
Moreover, How do I reset the code on my Samsung dryer?
Samsung error HC or HE
- Turn off the dryer for 20 minutes.
- Turn on the dryer and restart the cycle.
- Not working? …
- Simultaneously press the 2 buttons (depending on the model) ‘time’ and ‘mixed laundry’, or ‘dryness level’ and ‘mixed laundry’.
- Turn on the dryer.
How do I clear the HC error on my Samsung tumble dryer?
Samsung error HC or HE
The hot air compressor may be overheated. Turn off the dryer for 20 minutes. Turn on the dryer and restart the cycle.
How do I get rid of he error on Samsung dryer?
For fixing the failure enter the service mode. Turn on the dryer and hold the signal and temperature button for 3 s until you hear 3 loud beeps. This means that the service program was opened. When you see the sensor data on the panel disable the dryer, wait for 1 minute and run it again.
When I press the start button on my dryer nothing happens?
If your dryer won’t start when you push the start button, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. … If it doesn’t turn on, it’s likely that the dryer has no power. Check your power cord and the house circuit breaker.
How do I know if my thermal fuse is blown?
How to tell if a thermal fuse has blown? To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
Why isnt my Samsung dryer working?
When your dryer doesn’t power on, it could be something as simple as a tripped breaker or loose power cord. … Always switch off the circuit breaker before interacting with the dryer’s power cord, to avoid electric shock.
Why is my Samsung dryer not starting?
If your Samsung dryer lights up but won’t start, make sure the door is properly closed and latched. As a safety precaution, the drying cycle won’t begin until the door is closed and the latch is engaged. To engage the latch, close the door firmly and make sure loose clothing isn’t interfering with its closure.
How do you test a dryer control board?
How to test your dryer’s rotary switch: Unplug your dryer and remove the control console panel on the top of your dryer to locate the rotary switch. Set your multi-meter to the Rx1 setting and place the probes on the switch’s terminals. You should receive a reading of infinity.
Why did my dryer suddenly stop working?
Heat and controlling heat are essential to the dryer’s function. … A faulty or broken thermostat can make a dryer stop working. Replacing the fuse or the thermostat will allow the dryer to work again. A blown thermal fuse from overheating indicates an additional problem, such as improper ventilation.
Can I bypass thermal fuse on dryer?
If you do not have access to a multimeter or ohmmeter, you can momentarily bypass the thermal fuse. … Operating a dryer with a bypassed thermal fuse is both unnecessary and unsafe, so a bypass should only be done long enough to troubleshoot a potential problem.
Will a dryer start with a blown thermal fuse?
While a blown thermal fuse is the most common reason a dryer won’t start, run, or heat, you should remove the fuse from the appliance and test it to determine if it has blown or not before purchasing a new one. On electric dryers, the thermal fuse is often located on the blower housing or near the heating element.
What is wrong with a dryer when there is no heat?
Few things are more frustrating than finding your clothes wet after the dryer runs. Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. … Other potential reasons include a faulty thermal fuse and broken heating element.
How do you unlock a Samsung front load dryer?
To activate/deactivate the Child Lock press both the Drying Level and Time buttons simultaneously for 3 seconds. The Child Lock will light up when this feature is activated. When Child Lock is activated, you will not be able to press any buttons other than the power button until the Child Lock is deactivated.
Why is my Samsung steam dryer not working?
If your Samsung dryer is not heating up, in 80% of the cases it is caused by a burnt heating element, the other 18% being a blown thermal cut-off fuse, cycling thermostat, or a failed control board heater relay. The last 2% caused by an improper power supply.
How do you know if your dryer is dying?
If your clothes come out of the dryer feeling like they’re on fire, it doesn’t mean your dryer is working extra well; this might be the prelude to an actual fire. Too-hot temperature is one of the signs of a dying dryer. If your dryer starts making weird noises, or something is off, the dryer has a problem.
How much is a thermal fuse for a dryer?
Other Costs to Fix a Dryer
| Part | Material Cost | Total Cost |
|---|---|---|
| Thermal fuse | $5-10 | $80 -$130 |
| Dryer thermostat | $3-20 | $180 |
| Bearing | $50 | $130-$250 |
| Roller | $10-30 | $90-$230 |
What to check if dryer stops working?
Unplug the dryer and check the thermal fuse for continuity. Replace the thermal fuse if the multimeter measures no continuity. Check the exhaust vent because a clog in the vent likely caused the thermal fuse to blow. For dryers with a dial timer, a broken push-to-start switch can prevent the motor from running.
How do you unclog a dryer vent?
How to clean your dryer vent in 6 easy steps
- Step 1: Find your vent. Before you can clean your dryer vent, you’ll need to figure out where it actually is. …
- Step 2: Carefully disconnect your dryer. …
- Step 3: Vacuum the lint. …
- Step 4: Get in there with a brush. …
- Step 5: Clean up and reconnect. …
- Step 6: Celebrate.
How do you know if your dryer sensor is bad?
If your Whirlpool dryer leaves clothes damp, you may have a defective moisture sensor. A common symptom of a failed sensor is a Whirlpool dryer not drying all the way. The dryer moisture sensor is designed to detect the moisture level in the dryer and adjust the dry cycle time accordingly.
How do you tell if a thermal fuse is blown without a multimeter?
Testing By Bypassing The Fuse
If you do not have a multimeter, you can also test whether or not the fuse is working by bypassing the fuse itself. Simply detach the wires from the fuse, wire them together using a jumper wire and attempt to operate the dryer.
Where is the thermal fuse on my dryer?
The thermal fuse will be located somewhere by the exhaust vent on your dryer. You will be able to visually identify it by the two wires connecting to it. Removing the front of the dryer and removing the drum might be easier to access the fuse’s location.
What would cause my dryer not to start?
Common dryer issues include a faulty door switch or start switch and control problems such as a broken dryer timer or faulty electronic control board: … If the drum light doesn’t turn off, a failed door switch is the likely reason the dryer won’t start. A blown thermal fuse often prevents an electric dryer from starting.
