Reset. When the “F21” error code appears, try pressing “Pause/Cancel” to stop the current wash cycle. If water remains in the washing machine tub, touch “Drain/Spin” to force a secondary drain cycle to remove the water. Once all the water drains, try selecting a new wash cycle and pushing “Start.”
Likewise, How do I fix error code F21 on Maytag?
What is an F21 or F02 Error Code on my Maytag Front Load Washer? These error codes indicate that drain times are longer than expected .
…
Removing the Error
- Unplug the washer or disconnect the power for one minute.
- Plug in the washer or reconnect the power.
- Re-select the cycle and press Start.
Also, How do you reset a Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
Moreover, What does Code F 28 mean on a Whirlpool washer?
Posted: 08/01/17. shantapanchu a F28 error code is a common problem indicating that there is a communication problem with the central control unit. Any error code can be caused by a electrical anomaly. try to reset your washer.
Why is my Maytag washer not working?
When your washer isn’t working right, the solution may be as simple as switching up detergents, tightening a hose or leveling the appliance. … If you have a front load washer, a dirty drain pump filter can be a common cause of the issues listed below, like problems draining, spinning and odor.
How do I clear the error code on my Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
What does F21 mean on a Maytag 3000 washer?
In this particular case, error code F21 indicates an issue with your Maytag washing machine’s drain valve. When it takes eight or more minutes for a Maytag washing machine to drain, the device will tell its pipes to close, and you’ll be forced to troubleshoot.
Does Whirlpool washer have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
Where is the reset button on Whirlpool washing machine?
Is there a reset button on a Whirlpool washer? Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds.
What does F28 code mean?
The F28 code is displayed when your boiler fails three ignition attempts, resulting in the boiler halting operation and turning off. Vaillant officially defines the F28 error code as an ignition fault.
How do I reset my Whirlpool Duet washer?
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.
How do you fix a Maytag washer that won’t start?
The washer won’t start if the lid switch is defective. Disconnect the washing machine from the power supply and open up the housing. Examine the switch to see if it has any burn marks on it or if it’s corroded. Order a replacement part from Maytag or an authorized parts dealer if the part appears damaged.
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.
What causes a washing machine not to start?
You should check the outlet to make sure it’s working. Then, check if a fuse is blown or a circuit breaker thrown. If those both work, see if the Delay Start button or Control Lock feature has been activated. Sometimes it’s as simple as opening and closing the door to reset the washer.
What does F5 mean on washing machine?
The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range.
What does F5 mean on a washer?
A temperature sensor resistance that is out of the normal range is detected by the Central Control Unit. A failed NTC temperature sensor is what causes the F5 error.
What does the error code LF mean on a Whirlpool washer?
When “LF” is displayed, there could be an issue with the water flowing into the machine. … This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.
Can you reset a Maytag washer?
In addition to a number of heat and tumbling settings, many Maytag washers also have digital displays that indicate the minutes left on a washing cycle, which settings you have chosen and error messages. … You also can reset the washer if you want to cancel a setting you chose.
What does F mean on my Maytag washer?
Maytag F/02 – Drain Cycle Too Long
The manufacturer has assigned this error or fault code to indicate that the washing machine drain cycle is taking too long. After 8 minutes of drain time the error code is displayed. … If the error code returns, check to be sure the drain hose isn’t clogged or kinked.
How do I tell what year my Maytag washer is?
If a receipt or other paperwork is not available, the age of a Maytag washer can be found by looking at the serial number. The last two characters of the 10-digit number indicate the year and month of manufacture. A Maytag washer serial number is 10 characters long, with the last two characters being letters.
Why does my Whirlpool washer not turn on?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
Why is my Whirlpool washer stuck on sensing?
A blinking sensing light indicates an underlying issue with the drain, spin, or any other function. There are several such problems that Whirlpool washers commonly run into. … The washer will function only when the lid/door is completely closed. The water pump belt in the washer has worn out or is damaged.
Why is my Whirlpool washer not draining?
If your washer’s drain hose is kinked or bent, the washer will not be able to drain properly. The drain hose may also be obstructed by a small article of clothing. Check your drain hose and remove any obstructions, and straighten it if it’s bent. Make sure the hose is placed less than eight feet above the floor.