Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.
Table of Contents
READ ALSO
Likewise, Why does my Fisher and Paykel dishwasher keep beeping?
The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked. Ensure the drainage hose and connection to pipes are not blocked. Press ► once to stop the beeping, and then again to clear the fault. / ► to resume the wash program.
Also, How do I fix E6 error on Fisher and Paykel dishwasher?
Fisher and Paykel Dishwasher Dishdrawer Error Code E6 = The first 4 program indicator lights are flashing. Error Code Cause: Flood switch activated. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset. Check Flood Switch.
Moreover, How do I fix E4 error on dishwasher?
Error message E4 in integrated compact dishwasher indicates failure of communication between main PCB with display PCB.
…
Resolution:
- Make sure that the drain hose is correctly connected.
- Make sure that the filters in the appliance are clean.
- Make sure that the kitchen sink drains correctly.
How do I fix the f2 on my Fisher and Paykel dishwasher?
Reset Procedures for the Fisher & Paykel Dishwasher
Press the power button to turn off power to the Fisher & Paykel dishwasher. Wait a few minutes and then press the power button to restore power. Turn off and unplug the dishwasher if the issue remains.
How do I get my DishDrawer to stop beeping?
Sometimes, the beeping error on Fisher and Paykel DishDrawer Dishwasher is just abnormal, and may be fixed by simply resetting it. To do so, turn it OFF and after 10-15 minutes, turn it ON it.
How do I fix A6 error on Fisher and Paykel dishwasher?
foaming may also trigger an A6 fault.
- Open the drawer and check the spray arm.
- If the spray arm has loosened or come off its mounting, re-fit it. …
- Press ► once to stop the beeping, and then again to clear the fault.
- Press. …
- If the fault code persists, check the filter on the inlet hose is not blocked, and clear if needed.
What does E6 mean on dishwasher?
An E6 error code of the Bosch dishwasher means that there are problems with the sensor that controls the water turbidity. It is also called the Aqua Sensor. In the dishwasher, this sensor detects the turbidity of the water due to the presence of small particles of dirt, food residues and other things inside it.
Where is the flood switch on a dishwasher?
The anti flood switch is in the bottom of the bas of the dishwasher. If its activated try and pull the dishwasher out and tip it 45 degs backwards and the water should drain out from the base and that way the flood switch will reset itself.
What does E2 mean on dishwasher?
E2 – Abnormally long drain time. Check to make sure that the drain line is not obstructed or bent in a way that restricts water flow. Make sure the drain line is routed below the height of the dishwasher and that it has not been extended. This will inhibit the ability of the drain function to operate properly.
Why does my dishwasher keep saying E4?
E4 – Overflow sensor. Water pressure may be set to high. The inlet hose may not be properly connected. There is a malfunction or problem with the drain check for an obstruction.
How do I reset my E4 dishwasher?
Comments: E4 unplug and unhook. Disconnect the overflow, tilt and drain. I unplugged the dishwasher, cleaned out all water and trap, dry everything inside, unhooked the overflow and drain remaining water out, plugged it in and it worked.
Why is my dishwasher flashing E4?
The error code e4 in the dishwasher stands for “too much water.” This may mean that one of the pipes is leaking, or a plug in inlet hose has deteriorated, which is why liquid has accumulated in the tank with a volume exceeding the permissible norm.
What does F9 mean on a dishwasher?
A water pressure sensor is related to the F9 fault code on Glow-Worm boilers.
What does E2 mean on a dishwasher?
E2 – Abnormally long drain time. Check to make sure that the drain line is not obstructed or bent in a way that restricts water flow. Make sure the drain line is routed below the height of the dishwasher and that it has not been extended. This will inhibit the ability of the drain function to operate properly.
What does F2 mean on a dishwasher?
If your dishwasher doesn’t drain properly, you’ll see standing water on the bottom of the dishwasher when the cycle is complete and the error code F2 may be displayed.
Why is my Elba dishwasher beeping?
Blinking lights and beeping sounds can be caused from a power surge. So its beeping and flashing once per second correct this beeping and flashing is an error code that your unit is giving blinking lights or beeping sounds may indicate a problem with the dishwasher caused by power surges.
What does E9 mean on Fisher and Paykel dishwasher?
Answers : The fault E9 means the controller has a problem. Obviously it is not a complete fault as you are still getting the fault codes. Some key circuit in the controller has become faulty and this prevents dishwasher from working. Usually the controller needs to be replaced.
How do you reset the flood switch on a dishwasher?
If you dont, you will need a new anti-flood switch. But try this first, turn off power to your dishwasher at the mains! Then you have to remove the dhswasher and tip it towards you about 45 degrees and hold it there for 30 seconds, then you can stand it up again.
How long does a dishwasher last?
The average lifespan of a modern dishwasher is approximately 6-10 years. Over time, major components like the motor or pump may wear out, and out-of-warranty repairs can easily run $400-$600 or more once parts, labor and trip costs are calculated.
How do I fix i30 error on my dishwasher?
Error i30: description
When the tank is full, fluid drains into the bottom of the pan. Then the float switch actuates, the dishwasher interrupts the cycle and displays error code i30. Try rebooting it by unplugging it for 30 minutes.
How do you Unflood a dishwasher?
To solve this problem, we recommend cleaning the food with a sponge and a few drops of dishwasher detergent. In addition, pour vinegar into the detergent tray and run a short cycle while the unit is empty. Ignoring routine maintenance can lead to severe leaks too.
How do I reset anti flood system on dishwasher?
But try this first, turn off power to your dishwasher at the mains! Then you have to remove the dhswasher and tip it towards you about 45 degrees and hold it there for 30 seconds, then you can stand it up again.
