IMO you should get the best quality 3/4 plywood you can find (as many plys as possible) rip it to width, then glue 2 layers of that plywood together to make a 1 1/2″ thick shelf. If desired, you could cap the cut ends with solid wood.
similarly, How much weight can a 2×4 shelf hold?
Modern 2x4s are probably stronger than you think. Under optimal conditions, a single 2×4 can support about 1,000 pounds, or half a ton vertically.
on the other hand, What type of plywood should I use for garage shelves?
We use 1/2″ plywood for the 16″ width shelving – perhaps go up to 5/8″ or 3/4″ if you do 24″ wide shelving or have especially heavy loads destined for these shelves.
also, How thick should OSB be for garage shelves? How To Build Basic Garage Storage Shelving
- 4 sheets 7/16” OSB (or 1/2” plywood )
- 7- 2X4s by 8 feet long.
- 6- 2X2s by 8 feet long.
- 3 inch nails or screws.
- 1-1/2 inch drywall screws.
Is MDF good for garage shelving?
Because it’s inexpensive and fairly durable, medium density fiberboard s a good choice for practical projects like shelving and storage cabinets. … MDF is basically sawdust and glue, fused together under pressure and heat.
Are 2 2×4 as strong as a 4×4?
When used vertically, 4x4s are stronger than two 2x4s. However, if you need a horizontal surface, two 2x4s will be stronger than one 4×4. A 4×4 should not be used horizontally for anything structural.
Is a 2×4 stronger on its side?
2xs are always stronger on edge, consider how a header is constructed. Obviously it’s easier to drill thru the flat side. You might consider using both flat and on edge – connected together.
Can you build a deck with 2×4 joists?
2×4 Deck Joist Can Only Span 5’8″ (1.72m) Between Supports. Either you are limited to a small deck, less than 6′ (1.8m), or you will need a mid-span beam. … Three 6×6 posts, one on each end plus at mid-span, allow you to use 2×4 joists but is still strong enough to not flex with every step.
How thick should wood be for shelves?
Thick Wood Bookshelves
Use 3/4-inch thick materials for shelves and bookcase structure. If you’re using hardwood solids, it’s OK to boost the thickness to 1 1/4 inch for almost unlimited support. This type of shelf looks more like a mantel and is expensive, but adds the opulent look of craftsmanship.
How far can a shelf span without support?
The span limit is defined as the maximum distance apart that you can place the shelving supports. Glass, particleboard, solid lumber, plywood, and other common shelving materials can have span limits that can range from 18 inches to almost 5 feet.
How thick should garage shelves be?
The dimension of shelf width is hotly debated, but we settled on a depth of 16 inches. It’s deep enough to support tool cases and standard boxes, but shallow enough as to not lose stuff in the back and have to reach to far.
How thick should a garage shelf be?
How deep should garage shelves be? – The depth of your shelves may depend on what you plan to store and how much space you have in your garage. Garage shelves typically range from 12 – 24 inches deep.
Is OSB strong enough for shelving?
OSB is a great sheathing material but I certainly wouldn’t use it anywhere it would be visible. Even painted, it will not be a smooth surface and it will delaminate if it gets wet. The big box plywood gets a bad rap but for shelving, if a hardwood face is attached, it will work fine.
Can you use brad nails on MDF?
Puckers and mushrooms are less likely to occur in molding-grade MDF because the less-dense material at the site of the nail head allows for more material expansion. Slim, “needle-style” 18-gauge brad nails work best in pneumatic nailers. … You can, of course, use screws with MDF.
What are the disadvantages of using MDF?
What are the downsides of MDF?
- Engineered wood is easy to damage. One of the main differences between solid and engineered wood is the surface. …
- MDF is heavier. …
- MDF is vulnerable to extreme heat Remember that engineered wood is made out of wax and/or resin-like compounds. …
- MDF can’t support too much weight.
Is particle board good for garage shelving?
Particleboard is one of the workhorses of the building industry. It’s routinely used for standard shelving. However, if you want to build heavy-duty shelving, choose heavy-duty particleboard. Most particleboard shelves are 3/4-inch thick, but for heavy-duty applications use 1-inch thick particleboard.
How much force does it take to break a 2×4?
It would probably take over a thousand pounds to break a 2×4 in half on its short length.
Can you use 2×4 as a post?
3 Answers. 2 2x4s are not square, if that matters (3 x 3.5). They will be plenty strong as assembled posts. Try a traditional lumber yard, they will have untreated pine.
Are two 2×4 as strong as a 2×8?
Your statement about 2- 2×4 not being as strong as one 2×8 or one 2×10 is technically correct because the height is different for each one (not apples to apples). Referring to the code tables is a little misleading. Double stacked beams (not glued together) each carry half the load.
How far can a 2×4 span without sagging?
Generally, 2x4s can extend for up to 20 feet, but a number of issues have to be considered. For instance, the 2×4 would not noticeably sag under its weight at 10 feet.
How much force can a 2×4 take?
Assuming that the load is square and there is no wind, the average 8 feet 2×4 could handle around 1,000 pounds vertically. Of course, it’s wise not to push the material up to its limit, use brace and alike to secure the 2x4s whenever it’s needed.
How far can a 2×4 span laying flat?
If you use 5/4 decking, joists must be no farther apart than 16 inches. Decking made of 2x4s or 2x6s can span up to 24 inches.
How far can you span a 2×4 deck joist?
Decking Board Considerations
If you use 5/4 decking, joists must be no farther apart than 16 inches. Decking made of 2x4s or 2x6s can span up to 24 inches.
How far can you cantilever a 2×4?
The distance your joists can safely cantilever or overhang a drop beam is determined by the size of the joists, the wood type and grade of the lumber and the spacing between joists. Many building departments limit joist cantilevers to 24″ maximum.
Can a 2×4 span 10 ft?
Can a 2×4 span 10 feet? Generally, 2x4s can extend for up to 20 feet, but a number of issues have to be considered. For instance, the 2×4 would not noticeably sag under its weight at 10 feet.
Don’t forget to share the post !