Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds. Press the Pause / Cancel / Stop button twice to clear the display.
Table of Contents
READ ALSO
Likewise, How do I clear the error code on my Kenmore washer?
You will need to remove the power supply to the washer to reset the code.
- Look for the “Pause/Cancel” button on the washer control panel. …
- Press the “Pause/Cancel” button twice to cancel the wash cycle. …
- Connect the water supply hoses back to the washer and turn on the water spigots.
Also, How do I reset my Kenmore top load washer?
How do I reset my Kenmore washing machine?
- Press the “Stop” button twice, and then press the “Power” button.
- Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
- Press the “Start” button to complete the reset process and restart the washing machine.
Moreover, What would cause a Kenmore washer not to spin?
If your Kenmore Washer Model 110 isn’t spinning, there could be a variety of reasons why. The most common reasons are a broken drive belt or a defective door latch. It could also be a faulty motor control board or drive motor, or there could be a damaged stator or rotor.
How do I reset the F5 on my Kenmore washer?
It goes through the wash cycle and then ends with an F5 error and recurring beeping alarm. The “lid locked” LED flashes as well. The only way to clear the codes is to unplug and let sit, and then plug back in.
What does F mean on Kenmore washer?
The F indicates that the washer control detected a component problem. … If the F code was caused by excessive suds preventing the washer from draining, you may be able to shut the door and run a drain/spin cycle to remove the water from the washer.
How do I troubleshoot my Kenmore washer?
Kenmore 110 Series Washing Machine Troubleshooting
- Washer will not stop when the lid is open. “When you open the lid the washing machine will not stop what it’s doing.”
- Bad lid switch. …
- Water will not drain out of the washer. …
- Clogged waste hose. …
- Bad drain pump. …
- Bad pump motor. …
- Washer does not spin/agitate. …
- Broken drive belt.
How do you run a diagnostic on a Kenmore washer?
Close the door with the washer empty. Select “Drain/Spin” or “No Spin” by pressing the SPIN SPEED button. Within 5 seconds, push the “Prewash” option four times. The diagnostic should begin when C:00 light up.
How do I reset my top load washer?
Motor Reset Procedure:
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
- The motor has now been reset and is ready for you to start a cycle.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
What causes a washer not to agitate or spin?
The washer transmission might be worn out or defective. Transmissions have gears in them that can fail causing the washer to not spin or agitate. … If the motor is turning the transmission, but the washer won’t spin or agitate, consider replacing the transmission.
How do I make my Kenmore washer spin only?
- To perform a spin only cycle: Press the power button to turn the washer on. Press and hold the spin button for 3 seconds. …
- Yes, hold spin only at center bottom of key pad. Has asterisk next to it. …
- Press spécial care then spin only. …
- Spin towels. …
- Press on then special care then spin only. …
- Just put it on spin, and it will.
Why is my washer blinking F5?
5 Answers. If during the water heating step in the wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, the “F/05” error code will be displayed.
What is F5 error code?
An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions.
What does F5 on my washer mean?
A temperature sensor resistance that is out of the normal range is detected by the Central Control Unit. A failed NTC temperature sensor is what causes the F5 error.
How do I fix the F11 code on my Kenmore washer?
To clear and restart the control follow the these steps: Unplug or turn the circuit breaker off for 10-20 minutes. Reconnect the unit to the power source by turning the breaker back on or plugging the washer back in. Press the Pause/Cancel/Stop button twice to clear the display.
What does IE mean on a Kenmore washing machine?
The IE code indicates that the washer detects a problem with water fill. Make sure that the hot and cold water supply faucets behind the washer are fully open. If you are using Floodsafe fill hoses that are shown in the image below, then I recommend that you replace those with conventional fill hoses.
How do I reset my Kenmore front load washer?
To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.
Why won’t my Kenmore washer wash?
If the Kenmore washer gets stuck on the wash cycle, a temporary fix would be to manually spin the basket. This issue is likely the result of a faulty timer, water line valve, or lid switch. Meanwhile, check the line fuse or user control and display board if the washer won’t start the wash cycle.
How do I reset my Kenmore washer 110?
How do I reset my Kenmore washing machine?
- Press the “Stop” button twice, and then press the “Power” button.
- Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
- Press the “Start” button to complete the reset process and restart the washing machine.
What would cause a Kenmore washer not to drain?
If the washer won’t drain water the drain pump might be defective. It’s also common for a small sock or other article of clothing to get caught in the drain pump or in the drain hose. Check both for an obstruction before replacing the pump. If the washer won’t drain there might be a clogged pump or hose.
How do you troubleshoot a Kenmore 500 washer?
Troubleshooting Guide for a Kenmore Washer 500 Series
- Check to make sure that the washing machine is properly plugged into a grounded, three-prong electrical outlet.
- Check your fuse box or circuit breaker to make sure that the fuse is not blown or that the circuit breaker is not tripped.
How do you run a diagnostic on a Kenmore front load washer?
Here is what I did to run a diagnostic.
- With the washer empty, close the door.
- Push “control/on” or “Start”
- Select “Drain/Spin”
- Select “No Spin” by pressing SPIN SPEED touchpad.
- Push “PREWASH” option four times within 5 seconds. …
- C:00 should light up and begin the diagnostic.
How do I reset my Kenmore 500 washer?
How do I reset my Kenmore washer Series 500? Top Load Washer – Hydrowave Motor Reset Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
