Both plumber’s putty and silicone are sealing compounds designed to provide a water tight fit for pop up drains, sink strainers, undersides of fittings, showers and drains. Plumber’s putty is more traditional while silicone caulking is a more modern product, but either one (in most cases) can get the job done.
similarly, Can a sink drain go straight down?
In a sense, all drains go through the floor. You cannot have a code-approved sink drain going down, unless you have a vent going up.
on the other hand, Will plumbers putty stop leaks?
Plumber’s putty seals the parts to prevent leaks. A common location for leaks, and thus putty, is around toilets and drains. Putty also helps seal the drains for sinks and tubs.
also, Do you have to put plumbers putty on sink drain? The plumber’s putty must always be applied at the bottom of the sink and the sink must be placed with all the pressure on the countertop. Tips for using plumber’s putty. Even though the putty is better than the silicone and caulk in several situations, the plumber’s putty cannot stand as a solution in all areas.
Why can’t you use plumbers putty on plastic?
The putty can attack the chrome plating on the plastic drain and cause it to come off. Usually, plastic drains have a “foam” or rubber gasket to place under the drain “flange” so you do not have to use any sealant.
Can a p-trap be higher than the drain pipe?
It is not ideal to have the p-trap below the the exit drain because water gravity has to force the water out instead of it flowing downwards naturally. They both work and have seen it many times. But essentially anything below already creates its own p-trap- so using another is redundant.
Can you put a 90 in a sink drain?
It’s fine to have a larger-radius (sweep) 90-degree bend at the base of a vertical drainage stack where the wastewater starts to travel horizontally. It’s also a good idea to have a sweep 90-degree fitting where a drain pipe pops out of a wall for a kitchen, vanity or laundry sink.
Why is s trap illegal?
Back to “S” traps – The reason “S” traps aren’t allowed is because they have the potential to suck, or ‘siphon’, water out of the trap as the water flows down the drain. … Believe it or not, enough water to break the water seal at the trap and let sewer gases come in to the house.
What is the best sealant for leaking pipes?
The following list looks at the best pipe thread sealant for a number of applications.
- BEST OVERALL: Gasoila – SS16 Soft-Set Pipe Thread Sealant with PTFE.
- BEST BANG FOR THE BUCK: Dixon Valve TTB75 PTFE Industrial Sealant Tape.
- BEST FOR WATER: Oatey 31230 Pipe Joint Compound with PTFE with Brush.
How do I temporarily fix a leaking pipe?
How To Temporarily Patch A Leaky Pipe While You Wait For A Professional
- Apply A Water Pipe Epoxy. …
- Use Pipe Wraps. …
- Take Advantage of Pipe Clamps. …
- Utilize Rubber Pipe Connectors. …
- Invest In Some Plumbing Repair Tape. …
- Implement Repair Sleeves.
What can I substitute for plumbers putty?
A clay-like substance called plumber’s putty is the most popular choice for sealing sink drains, but you can also use silicone caulk.
- Most Popular: Plumber’s Putty.
- Plumber’s Putty Installation.
- Alternative: Silicone Caulk.
- Silicone Caulk Installation.
Can you use too much plumbers putty?
It is normal for excess putty to ooze out when you tighten the fixture. How much depends on “how too much you applied to the basket strainer assembly. If you apply way too much and do not get it tight hot water will wash it out. If you apply the right amount and tighten it enough it won’t wash out in 20 years.
What can be used instead of plumbers putty?
If you do not have plumber’s putty or cannot use it on your type of sink, then you can use silicone or even the foam or rubber gasket that comes with some pop-up assemblies. Fit the drain or fixture into its appropriate place, and this will ensure a watertight fit and limit the chances of having a leak.
Can you use sealant instead of putty?
Old, dry putty can be softened with bleach and linseed oil. Either acrylic latex/silicone caulk or window putty, also known as glazing putty, are commonly used for this purpose. … Both types will work, but one has proven its superiority with the test of time.
How far below drain should p-trap be?
However, the Universal Plumbing Code stipulates that the total developed length of all tailpieces, arms and fittings connecting the drain to the p-trap must be 24 inches or less.
What can I use instead of p-trap?
Recently I discovered the amazing HepvO Waterless Valve. It’s a new solution to this old problem. Using a flexible silicon tube inside that seals out air but allows water to flow in one direction, it performs the same task without using any water and without being large and bulky like a p-trap.
Does p-trap have to be directly below shower drain?
If you install TWO “P” traps the shower will NOT drain. The “P” trap SHOULD be directly under the drain, but no more than a few inches off center of it, if conditions require it. NO trap, TWO traps, and/or a 9 foot offset are NOT allowed and if he suggests any of them get a different installer who is a REAL plumber.
How many turns can a drain pipe have?
According to plumbing code, drain pipe has to be sloped a minimum of 1/4-inch per foot and a maximum of three inches per foot or vertical. A slope of less than 1/4-inch per foot will cause constant drain clogs and a slope of more than three inches will allow the water to drain without the solids.
How far below drain should P trap be?
However, the Universal Plumbing Code stipulates that the total developed length of all tailpieces, arms and fittings connecting the drain to the p-trap must be 24 inches or less.
Can plumbing vent pipes have 90 degree angles?
Vent pipes, often narrower than drainpipes, need not slope like drainpipes. … Vent pipes must be installed so they stay dry. This means that they should emerge from the top of the drainpipe, either straight vertically or at no less than a 45-degree angle from horizontal, so that water cannot back up into them.
Which is better P-trap or S trap?
P-traps are generally considered by most to be more effective and consistent in maintaining water trap compared to S-traps. Their design makes them less vulnerable to drying out and losing seal: a properly installed P-trap will never lose its water seal.
What is the difference between a J bend and a P-trap?
The J-bend beneath the sink is also referred to as the P-trap, the U-bend and sometimes even just the drain trap. … In some cases, however, hand-tightening may not seat the washer correctly, particularly if your drain pipes are metal, so slip-joint pliers will often come in handy.
Do you need 2 P traps for a double sink?
A double bathroom sink installation rarely requires more than one P-trap. The usual practice is to connect the two sinks to a tee and then feed the tee into a single P-trap, which then connects to the drain. The pipes you use to connect the sink to the P-trap are the same type the P-trap is made from.
Don’t forget to share the post !