One of the most common reasons for a Maytag top load washer not spinning is an incorrect wash cycle or spin setting. GENTLE, HANDWASH, or DELICATE settings utilize slower spin speeds for more fragile fabrics. Some model washers also allow you to vary the spin speed, making it slower or more rapid, for different loads.
Table of Contents
READ ALSO
Likewise, How do you fix a Maytag washer that won’t drain?
If the washer won’t drain or is not draining properly, and the washer has a coin trap, remove the coin trap and clean it thoroughly. First, check the drain hose to determine if it is kinked, twisted, or bent. If the drain hose is bent, straighten it out. In addition, remove the drain hose and check it for obstructions.
Also, Why isn t my washing machine spinning?
An imbalanced drum is a common reason for your machine not spinning. The easiest way to avoid an imbalanced drum is by making sure you don’t overload your washing machine, or if you have one large piece of laundry, add smaller pieces to balance out the load. You may also need to check that your machine is level.
Moreover, What’s wrong with a washer when it won’t spin?
An unbalanced load of laundry is one of the most common causes of an inadequate spin cycle. Sometimes clothing can settle on one side of the drum, throwing off the motion of the washing machine. … If you suspect a distribution problem, try rearranging your clumped-up wet laundry and running the spin cycle again.
How do you unclog a Maytag washer?
- Prepare the Machine. Pull Away from the Wall. With your supplies ready, it’s time to prep the washing machine. …
- Clear the Water. Bail Out the Basket. If the washer is full of water that isn’t draining away, you’ll need to bail it out. …
- Remove the Front Panel. Prop Up the Washer Front. …
- Start the Clog Hunt. Check the Pump Housing.
How do I know if my washing machine drain hose is clogged?
An easy way to check that the drain hose is clear is to blow air through it. If nothing is obstructing the drain tube, the problem is most likely at the washing machine pump. If the hose is worn or badly kinked, replacing the hose may improve the ability of the machine to pump water.
What causes a washer not to drain?
There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
How do you reset the spin cycle on a Whirlpool washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do you check if your washing machine is clogged?
Observe the washing machine as it pumps water into the hoses and up into the standpipe. If you see water back up and out of the standpipe, your washer’s drain is most likely the issue. The amount of time it takes for the standpipe to fill up and overflow helps you diagnose where the clog is located.
How do you reset a washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
What causes a Whirlpool washer not to agitate?
When your Whirlpool washer won’t agitate, spin, or drain, the culprit could be a defective drive block. The drive block connects the agitator to the washer transmission. … If the drive block is worn out, the agitator may move a little or not at all, even when the transmission shaft is still moving.
How do I know if my washing machine pump is broken?
When the pump fails, you can hear or see the trouble: a loud rumbling inside the machine, or a failure of the water to drain out of the tub. Here’s what you can do to fix the problem: Step 1: Check the drain hoses to make sure they’re draining properly. Remove the water supply hoses from the back of the washer.
How do you fix a Whirlpool washer that won’t drain?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
How do you unclog a washing machine drain line?
To unclog a clogged drain, first fill a bucket with boiling water and a pack of baking soda. Remove the drain pipe from your washing machine and slowly pour the water into the drain using a funnel. Wait a few minutes and test if it keeps draining if you pour water into it.
Why is my washer not draining or spinning?
If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.
How do you manually drain a washing machine?
How to Manually Drain a Top-Loading Washing Machine
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose at the back of the washing machine. …
- Step 3: Drain the water. …
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose. …
- Step 3: Drain the water. …
- Step 4: Scrub the filter.
What should I do if my washing machine won’t drain?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
How do you fix a washer that isn’t spinning?
- Redistribute an off-balanced load of laundry. …
- Level an off-kilter washer. …
- Check the power source. …
- Stop using an extension cord. …
- Inspect the spin switch. …
- Stick to high efficiency detergent with a front-load washer. …
- Undo any kink in the hose. …
- Track down a blockage in the drainage system.
Why is my Whirlpool washer not draining?
If your washer’s drain hose is kinked or bent, the washer will not be able to drain properly. The drain hose may also be obstructed by a small article of clothing. Check your drain hose and remove any obstructions, and straighten it if it’s bent. Make sure the hose is placed less than eight feet above the floor.
How do I fix a Whirlpool washer error?
If the Whirlpool washer displays the de error code on display, so there are problems with a door.
…
Manual Review
- Unplug the Whirlpool washing machine from the mains.
- Wait for 15-20 minutes while the control unit reboots.
- Reset the error by pressing the START button (On/Off).
- Check hatch locking.
How do you reset the code on a Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I know if my dishwasher drain hose is clogged?
A small amount of standing water in the bottom of your dishwasher is normal, but when the amout of water is above the drain and leaks onto the floor when you open the door, the dishwasher drain hose may be clogged.
