Dirty condenser coils are the most common cause for a Whirlpool refrigerator not cooling. Condenser coils dissipate heat as the refrigerant passes through them. If the coils are clogged in dirt and debris, they can’t release the heat properly.
Likewise, How do I run a diagnostic on my Whirlpool refrigerator?
Starting Diagnostics
To start with we need to start the refrigerator’s diagnostic mode. To do this open the refrigerator door and press one or both door switches, depending on your refrigerator type. Next press the refrigerator temperature (+) button three times in ten seconds and release the light switch or switches.
Also, What would cause my refrigerator to stop cooling?
Here are five other common reasons why your fridge may not be cooling, and how to address them.
- Condenser coils are dusty. …
- The condenser fan is broken. …
- The evaporator fan is broken. …
- Evaporator coils are covered in frost. …
- Air inlet damper is broken.
Moreover, What to check if refrigerator stops cooling?
Depending on what’s causing your fridge not to keep perishable foods cold enough, the following procedures might help.
- Make sure your fridge is getting power.
- Check the refrigerator’s thermostat.
- Test the seals on your fridge doors.
- Determine whether the refrigerator is level.
- Clean the condenser coils.
Why would a refrigerator stop cooling?
Problem: Fridge Not Cooling
Be sure the fridge is plugged in and getting power. … Vacuum the coils under or behind the fridge. Clogged coils can cause poor cooling. Check to make sure nothing is stuck in the condenser fan and that it spins freely (models with coils on the back won’t have a fan).
How do I force my Whirlpool fridge to defrost?
To run a forced defrost cycle open the refrigerator door or doors if your refrigerator is a french door model. Then hold down the door switch or switches, the display should go blank. Next press the refrigerator temperature (-) button 3 times in 10 seconds and release the door switches.
How do you fix a Whirlpool refrigerator that is not cooling?
A Whirlpool refrigerator not cooling may have a dirty or damaged gasket that leaks cold air, warming the refrigerator’s interior. Inspect the door gasket for damage, using a cloth dipped in warm water to clean away any dirt and debris. If the gasket is ripped or broken it will need to be professionally replaced.
Why would fridge suddenly stop working?
Typical causes are: 1) the door is left open frequently, 2) the condenser coils need cleaning, 3) the door doesn’t seal against the refrigerator box, 4) the cold control is set too cold, or 5) something is blocking the flow of cold air inside the fridge.
What is the first thing to check when a refrigerator stops working?
The first thing to check is the breaker (in your home’s electrical service panel) of the circuit serving the fridge.
What is the first thing to check when refrigerator stops working?
The first thing to check is the breaker (in your home’s electrical service panel) of the circuit serving the fridge.
Why would my refrigerator stop cooling and then start working again?
If the thermostat is adjusted incorrectly, the fridge will turn off and turn on again when the temperature increases. The compressors are responsible for providing power for the cooling process. In this case, it is suggested that you lower the thermostat setting to ensure the compressor keeps working properly.
What causes a refrigerator to not defrost?
One of the most common reasons your fridge may not be defrosting is a faulty timer. Issues with these parts are easy to diagnose, but the timer itself cannot easily be repaired. The best solution is to replace the timer.
How do you force a refrigerator to defrost?
To initiate a defrost cycle, open the door and push the light switch in and out 5 times within 6 seconds. The compressor and fans should shut off and the defrost heater should come on.
How long does it take to defrost a Whirlpool fridge?
Depending on the size and method, defrosting a refrigerator or freezer can take anywhere from 10 minutes to a day. The most common method is to unplug the refrigerator or freezer, prop the door open and allow the ice to melt on its own. However, this method may take up to a day to defrost the appliance completely.
How long should a Whirlpool refrigerator last?
A standard refrigerator can run up to 17 years on average. Your refrigerator’s life expectancy is affected by how well it is cared for. Some models run for up to 19 years, while others only last 10 years.
Why is my fridge compressor not working?
If the start capacitor is defective then the compressor may not start. Check for signs of overheating or arcing and replace if necessary. If the overload, start relay and capacitor check ok, then you may have a defective compressor which should be checked by a qualified technician.
Will unplugging a fridge reset it?
By unplugging the fridge for 24 hours, the ice melts. If the fridge starts cooling again, then you have fixed the immediate problem (iced coils) and possibly identified the root cause (bad defrost controller).
What should I do if my refrigerator stops working?
Grab a food cooler (or ice chest) and put a layer of frozen foods in the bottom. Then put a layer of foods from the fridge on top of that layer. Top it off with another layer of frozen foods. The frozen foods will keep everything cold while you run to the store to get a bag of ice and a fridge thermometer.
How do I reset my refrigerator compressor?
How to Reset the Compressor on a Fridge
- Locate the refrigerator power cord on the back of the appliance.
- Disconnect the power cord from the wall outlet. …
- Turn both the fridge and freezer controls to “Off” or “0” inside the fridge. …
- Adjust the fridge and freezer controls to the desired setting.
Why is my freezer frosting up and fridge not working?
Be sure the vents on the back of the freezer compartment aren’t blocked by boxes of ice cream or frozen vegetables—the vents have to be clear for cold air to circulate. Vacuum the coils under or behind the fridge. Clogged coils can cause poor cooling. … To do this, unplug the fridge and pull it out.
What are the symptoms of a bad defrost thermostat?
A faulty defrost termination thermostat may result in the defrost heater never heating and a solid frost buildup on the evaporator coil, which results in too warm temperatures. The thermostat contacts are normally closed and have continuity until it reaches 140 degrees.
What is forced defrost mode?
Force Defrost, indicated as “Fd” on the seven-segment displays, activates the ice maker’s heater loop as well. In fact, depending on the model you are working on, Force Defrost will also activate other electric heaters in the appliance.
How do you test a whirlpool Defrost Control Board?
The adaptive defrost control board will only go into Test Mode when the bimetal is closed. If it senses that the bimetal is open, then it will go back into cooling mode after somewhere between 4 and 8 seconds.
How often does a refrigerator go into defrost mode?
Most models will defrost for approximately 25 to 45 minutes, usually once or twice a day. You may hear water dripping or sizzling as it hits the heater. This is normal and helps evaporate the water before it gets to the drip pan.