The Error code LF stands for ‘Long Fill’. If the water filling time exceeds ten minutes, it means the water valves have turned off. LF flashes when the water level does not change for a period of time on or water is present but control does not detect the water level changing.
Likewise, How do you fix LF error on a hot tub?
For the error messages of HFL, LF, Dr, or DRY. This means that there is a flow issue through your heater. Try and clean your filters. While cleaning your filter make sure there is no debris in your hot tub that will get sucked down into your pump.
Also, How do you reset the code on a Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Moreover, Where is the water inlet valve located on a washing machine?
The inlet valve can be found on the back of your washing machine. Its principal responsibility is to manage the entry of water into your washing machine. In other words, the inlet valve acts as a sort of gate keeper, allowing water to flow into the tub when it receives certain electrical signals from the washer.
What does code LF mean on hot tub?
LF = Persistent low flow problems. (Displays on the 5th occurrence of “HFL” message with 24 hours). Heater is shut down, but other spa functions run normally. dr = Inadequate water detected in heater.
What does code SL mean on hot tub?
SL: Sleep –
Sleep mode will only allow the spa to heat within 20 degrees of the set temperature.
What does HL mean on hot tub?
The HL reading in the display stands for Hi-Limit. The hi-limit is measuring the temperature at the heater, not the actual water temperature of the spa. if your spa is reading HL, it will not allow your heater to turn on and therefore you will notice the pumps will be running close to 24 hours a day.
How do you bypass the clean cycle on a Maytag washer?
Hello Sandy, Press and hold the “Spin” and “Soil” button simultaneously for 10 seconds. A countdown will be displayed on the console. Once the countdown has completed the unit will have successfully reset.
How do you reset a Whirlpool washing machine?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
How do I turn off the control lock on my Maytag washer?
To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.
How do I know if my inlet valve is bad?
Signs that point to an inlet valve problem include leaks that fill the dishwasher when not running, the dishwasher filling too slowly when in use, or the dishwasher not filling at all. Leaks that end up outside of the dishwasher also can indicate an inlet valve problem, and this must be addressed immediately.
Can you fix a water inlet valve?
There is little that you can do to repair the valve itself, but you can clean the two inlet ports to restore full water flow. You can also test the valve to determine whether it has failed. Replacing a bad valve is a simple job and must be done with parts and procedures that are specific to your washing machine model.
What does f7 mean on a hot tub?
This sounds like a filter mode. See if all pumps are pulling proper water, and that the spa has good water flow back to spa.
What does F4 mean on hot tub?
The Big List of Spa and Hot Tub Error Codes
CODE | ERROR CODE DESCRIPTION |
---|---|
F4 | 8 hours daily filtration; system message, not an error |
F6 | 12 hours daily filtration; system message, not an error |
F | Fahrenheit, used to indicate panel is in Fahrenheit mode |
FB-ER | Fiber optic error; accent lighting |
How do I fix the HH code on my hot tub?
Open the spa cover and let the spa cool down for 10 minutes, then touch the control panel to reset the circuits, or push a red reset button on air systems. For OH, HH or HOT trouble codes, an overheating hot tub is not usually a heater problem. It is almost always a flow problem.
What does SL mean on CleverSpa?
A SL Error Code showing on your CleverSpa® Control Panel can mean there is a blockage in the system which is preventing hot water from circulating.
What mode should my hot tub be in?
By default filter modes are 2 hours in the morning and 2 hours in the evening, the rest of the time the hot tub will use the insulation to keep the spa warm and retain heat. Economy is a good setting for those who use the hot tub daily.
What does F4 mean on a hot tub?
The Big List of Spa and Hot Tub Error Codes
CODE | ERROR CODE DESCRIPTION |
---|---|
F4 | 8 hours daily filtration; system message, not an error |
F6 | 12 hours daily filtration; system message, not an error |
F | Fahrenheit, used to indicate panel is in Fahrenheit mode |
FB-ER | Fiber optic error; accent lighting |
Why is my Cleverspa saying HL?
An HL error usually means there is a blockage, preventing water from circulating around the pump & heating system.
Is there a reset button on a hot tub?
A spa heater has a high-limit reset button. A spa or hot tub provides a form of personal relaxation known as hydrotherapy. … A spa heater may need to be reset if it has tripped or stopped working. Using the high-limit reset switch and checking all breakers and GFCI outlets can reactivate the spa’s heater.
How do you use the clean cycle on a washing machine?
Add two cups of white cleaning vinegar to detergent dispenser. Run it through a complete cycle. Run another cycle on the highest level and at the hottest water temperature, this time adding one-half cup of baking soda to the drum. When cycle is done, wipe inside drum of washer with a damp microfiber cloth.
How much bleach do you put in a washing machine to clean it?
To clean your washing machine with bleach, simply add 60ml of neat bleach to your detergent drawer then run your machine on a hot cycle, with an extra rinse cycle to make sure all the bleach is flushed out. If you can smell any trace of the bleach afterwards, run another empty cycle to be on the safe side.
Why does my Maytag washer smell like rotten eggs?
For a rotten egg smell, it could be one of two things. The most likely is bacteria growing in your washer because of built-up dirt, mildew and mold, lint, and/or soap. … Natural gas is odorless so the utility companies add sulfur which gives it that rotten egg smell so it’s detectable when there is a leak.