Make sure both fuses are intact and tight, or that either circuit breaker has not tripped. You can test the breaker by turning the breaker off and then back on. Replace the fuse(s) or reset the circuit breaker(s). If the problem continues, call an electrician.
Table of Contents
READ ALSO
Likewise, When I press the start button on my dryer nothing happens?
If your dryer won’t start when you push the start button, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. … If it doesn’t turn on, it’s likely that the dryer has no power. Check your power cord and the house circuit breaker.
Also, Why is my Maytag dryer stuck on sensing?
Either your fuse has failed, the belt is broken, or your control board is bad. To determine which is your problem, you need to open the top panel of the dryer and make sure the belt is still tight around the drum. … If the fuse is bad, replace it. If the fuse is good, replace the control board inside the control panel.
Moreover, Why is my Maytag dryer not spinning?
A damaged or worn drive belt is one of the most common reasons for a dryer not to spin. … You can easily test whether your drive belt is broken. Try to turn the drum manually. If it spins easily by hand, the drive belt is probably broken.
Where is the thermal fuse located on my Maytag dryer?
Dryer thermal fuse (or thermal limiter). This fuse is located on the exhaust duct. If the dryer overheats, the thermal fuse opens to cut off power to the dryer. The thermal fuse cannot be reset–if the thermal fuse is open, it must be replaced.
What would cause a dryer to not turn on?
Common dryer issues include a faulty door switch or start switch and control problems such as a broken dryer timer or faulty electronic control board:
- Problems with the door switch can prevent the dryer from starting. …
- A blown thermal fuse often prevents an electric dryer from starting.
How do I know if my thermal fuse is blown?
How to tell if a thermal fuse has blown? To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
Where is the dryer reset button?
Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes.
Why is my dryer stuck on sensing?
All dryers stop when the door opens or the door switch detects the door opening, so a broken door strike, weak door catch or faulty door switch can cause the dryer to stop mid-cycle. A bad drive motor, failed timer or faulty electronic control board can also stop the dryer before the cycle ends.
How do you fix a dryer if it’s not spinning?
A broken drive belt is the most common reason a dryer won’t spin. To fix this issue, turn the drum by hand. A working belt should provide some resistance, so if the drum turns very easily and loosely, the belt is probably broken.
Why would a dryer turn on but not spin?
If the dryer doesn’t spin, it could be that the rubber drive belt looped around the dryer drum is either stretched out too much and not causing enough friction to turn. The dryer not spinning could mean that you have a broken drive belt.
How do you fix a Maytag dryer that won’t spin?
The rollers must spin freely to work properly. If the drum rollers are worn out, the dryer won’t turn properly. To determine if the support rollers are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the support rollers for wear.
How dO I know if my thermal fuse is blown?
How to tell if a thermal fuse has blown? To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown. Learn about testing for a blown fuse.
How do I know if my dryer thermal fuse is bad?
Touch the black lead to one of the fuse’s terminals and the red lead to the other terminal. If the meter display shows zero Ohms of resistance, the fuse has electrical continuity and has not blown, indicating that another component in the dryer is likely defective and preventing the appliance from running or heating.
Are all dryer thermal fuses the same?
All dryers sold in the United States are legally required to have a thermal fuse. This is different from the electrical fuses that are found in many appliances, and a dryer might have both. A thermal fuse will blow when the temperature gets too high, not when it’s drawing too much current.
What happens when thermal fuse blown on dryer?
A thermal fuse will blow when the temperature gets too high, not when it’s drawing too much current. … When it blows, the dryer stops generating heat. It’s necessary to replace it before the dryer will run again.
Can a dryer be fixed?
Most dryer problems can be fixed in an hour with a few basic tools and a continuity tester or multimeter—and you can do the work yourself with these simple instructions.
What causes a Maytag dryer to stop heating?
If your Maytag dryer is not heating, it is possible that it is not being supplied with the proper voltage. Most electric dryers require two legs of 120 volts AC that is equal 240 volts. If one leg of voltage is shut off by a tripped breaker or blown fuse, the dryer may be able to run but it will not heat.
Can a dryer thermal fuse be reset?
You can reset a thermal fuse. … It isn’t just clothes dryers that have thermal fuses; pretty much any appliance that heats up has one, including your washer, microwave oven, standard electrical oven, dishwasher and room heater.
Is it safe to bypass a thermal fuse?
Bypassing a Dryer Thermal Fuse
Operating a dryer with a bypassed thermal fuse is both unnecessary and unsafe, so a bypass should only be done long enough to troubleshoot a potential problem. Even short usage without a thermal fuse in place could result in irreparable damage to the appliance or injury to yourself.
Does unplugging a dryer reset it?
Resetting your dryer is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most), and then power it up again. That’s it. That’s all it takes to reset.
How much is a thermal fuse for a dryer?
Other Costs to Fix a Dryer
| Part | Material Cost | Total Cost |
|---|---|---|
| Thermal fuse | $5-10 | $80 -$130 |
| Dryer thermostat | $3-20 | $180 |
| Bearing | $50 | $130-$250 |
| Roller | $10-30 | $90-$230 |
Where is the thermal fuse on a Whirlpool dryer?
Remove the back access panel on the dryer, and look for the exhaust duct near the bottom of the unit. The thermal fuse is either circular or oblong, often white plastic with black material in the center and two wire leads. The thermal fuse is mounted on the exhaust duct.
