CL Error Code
CL is not an error code, but an indicator that the child lock feature is active. When the child lock feature is active, the control panel is disabled, and settings cannot be adjusted. To activate or de-activate child lock, press and hold the child lock button for 3 seconds.
similarly, Why is my washing machine blinking CL?
The “rL” error code means that a load has been detected in drum during Clean Washer with affresh® cycle. The Clean Washer cycle is meant to run empty, with no clothing inside the washer. Remove items from washer drum and restart Clean Washer with affresh® cycle.
on the other hand, How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
also, How do I clear the error code on my Whirlpool washer? To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Is there a reset button on the Whirlpool washer?
Is there a reset button on a Whirlpool washer? Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds.
What does F12 mean on Whirlpool washer?
F12 can be a heating element short or it has failed. F14 is a program memory, or EEPROM failure or fault. F15 is an error with the motor control. F16, F18, F20, F21, and F22 all indicate a problem with the control unit.
Does unplugging a washer reset it?
On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How do you reset a front load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
Does a washer have a reset button?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How do I reset my Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
What does E4 mean on a Whirlpool washer?
E4 – Open Lid alarm
If you have received an E4 error code, it means the lid has been opened during the spin cycle. Close the lid; washer operation will resume.
Why won’t my washing machine finish its cycle?
Drainage Problems
If the washing machine doesn’t drain properly then something blocking the pump could have caused the washer to stop mid cycle. … General overheating is again a possible cause for your washer to stop mid-cycle, many washing machines have built-in sensors.
How do I reset my top load washer?
Motor Reset Procedure:
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
- The motor has now been reset and is ready for you to start a cycle.
How do you fix a washer that won’t cycle?
These repairs may help solve your washer problem
- Replace the washer lid switch. …
- Replace the washer shifter assembly. …
- Replace the washer door lock assembly. …
- Replace the washer main control board. …
- Replace the washer timer. …
- Repair or replace the washer drain pump. …
- Replace the washer motor control board.
Why did my front load washer stop spinning?
Front-load washer tubs spin thanks to a drive belt that runs off of the motor. A loose, frayed, or torn belt could be why your washer won’t spin. Overloading your washing machine can cause the belt to loosen or become worn out. Inspect the drive belt closely.
How do I reset my defy front load washer?
First, you should perform a general reset of the machine. Turn the machine off at the powerpoint, wait for one minute, and then turn it back on. If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians.
How do you reset a washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do I reset my front load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do you manually unlock a Whirlpool front load washer?
Reach up inside the front panel and locate the door latch assembly on the right side of door. Feel for a tear-drop shaped tab on the bottom of the door latch assembly. This tab will manually unlock the door.
What does F5 and E2 mean on a washing machine?
The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.
What does F4 mean on washer?
If your washing machine is showing on your digital display or LED display an error code F4, or F8, this means you have a motor tacho not detected or no motor action, you need to check these: the motor tachometer. the wiring and connections to the motor and PCB. the motor carbon brushes.
What does E3 and F5 mean on a Cabrio washer?
The F5 E3 alert indicates there is issue with the lid lock. … Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. If this is unsuccessful, reboot the machine by unplugging the washer and wait two minutes before plugging the machine back in.
Don’t forget to share the post !
