An F20 or FH error code indicates a water supply problem. Here are some common issues: Both hot and cold water must be connected and turned on. Water inlet hoses kinked. Water inlet valve screen clogged.
Likewise, How do you clear F21 code on Whirlpool Duet washer?
Reset. When the “F21” error code appears, try pressing “Pause/Cancel” to stop the current wash cycle. If water remains in the washing machine tub, touch “Drain/Spin” to force a secondary drain cycle to remove the water. Once all the water drains, try selecting a new wash cycle and pushing “Start.”
Also, Why does my washer keep saying F20?
F20 Error Code
Whirlpool error code F20 appears when no water is detected entering the machine or if the pressure switch trip is not detected. The pressure switch is the part of the machine that monitors high water pressure. The washing machine automatically cancels the wash cycle during an F20 error.
Moreover, How do you run a diagnostic on a Whirlpool Duet washer?
Duet Washer Diagnostic Test Mode
Pick any three buttons on the Duet washer control except power, start, or cancel. Now do the key dance within eight seconds… Button 1, Button 2, Button 3, Button 1, Button 2, Button 3, Button 1, Button 2, Button 3 (You are pressing 9 buttons in 8 seconds so it needs to be pretty quick.)
What does F20 mean on a washer?
F20 Error Code
F20 indicates a water inlet problem—no water or insufficient water supply. Try the following method to resolve: Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
How do I fix my F21 whirlpool?
When the Whirlpool washing machine appears on display, the error code F21 does not drain the tank’s water.
…
To solve the problem , you need:
- turn off the washing machine by unplugging the power cord;
- move it away from the wall and turn it back towards you;
- disconnect the hose and inspect it for blockages.
How do I fix my f20 on my Whirlpool washer?
To reset the f20 error code, exclude the program crash of the Whirlpool washer. To do this, de-energize your washing machine for 10-20 minutes, then turn it on back. If the error disappears from the display, the problem is successfully eliminated.
How do I reset my Whirlpool Duet washer?
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.
How do you check the pressure switch on a Whirlpool Duet washer?
Use an ohmmeter to determine whether the pressure switch is malfunctioning.
- Unplug the Whirlpool Duet washer power cord from the wall outlet. …
- Go behind the Duet and remove the three screws securing the top panel to the rear panel with a Phillips-head screwdriver. …
- Locate the pressure switch inside the washer cabinet.
How do you reset a Whirlpool Duet front load washer?
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.
Is there a reset button on a Whirlpool front load washer?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
What does F22 mean on Whirlpool washer?
F22 indicates a front door lock issue. Try to following method to resolve: Select PAUSE/CANCEL twice to cancel the cycle.
How do you reset a Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
Where is the drain filter on a Whirlpool Duet washer?
The location of the drain pump filter in a Whirlpool Duet washer is accessible through the lower access panel below the washer door.
- Unplug your Whirlpool Duet washer power cord from the wall outlet. …
- Find the screws securing the lower access panel to the washer cabinet. …
- Remove the screws with a 1/4-inch nut driver.
What does FH error code mean?
FH Error Code
FH indicates that there is a Water Inlet Problem—no or insufficient water supply. Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
Why is my Whirlpool washer flashing F?
The “F” error code indicates the washing machine system or “Fault”. Ehe “E” error is indicating the part in your washer that causing the issue or “Error”. As a general rule, these “F” error codes mean the following… – Whirlpool Duet Washing Machine F1 error code indicates main control board and/or program faults.
How do you manually unlock a Whirlpool front load washer?
Reach up inside the front panel and locate the door latch assembly on the right side of door. Feel for a tear-drop shaped tab on the bottom of the door latch assembly. This tab will manually unlock the door.
Why is my Whirlpool front load washer not draining?
You need to make sure that the drain hose is not kinked at all. Straighten the hose to make sure that there is enough water flow and that you also remove any blockages from the drainpipe well. Ensure that you are using a U-shaped drain and secure it properly. Your instruction manual will show you how to do this.
How do I reset my Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
What does the Code F mean on a Whirlpool washer?
The F/dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. When the door fails to lock, the machine won’t run at all.
How do I reset my Whirlpool washer after a power outage?
How do I reset my Whirlpool washer after a power outage?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. …
- The motor has now been reset and is ready for you to start a cycle.
Why does my Whirlpool washer not start?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
Why is my Whirlpool washer not draining?
If your washer’s drain hose is kinked or bent, the washer will not be able to drain properly. The drain hose may also be obstructed by a small article of clothing. Check your drain hose and remove any obstructions, and straighten it if it’s bent. Make sure the hose is placed less than eight feet above the floor.
