The manufacturer has assigned this error or fault code to indicate that the washing machine drain cycle is taking too long. After 8 minutes of drain time the error code is displayed. Press PAUSE/CANCEL twice to clear the display. If the error code returns, check to be sure the drain hose isn’t clogged or kinked.
Likewise, How do I fix F5 on Maytag washer?
The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area.
Also, How do I reset my Maytag top load washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
Moreover, What are the codes for a Maytag washer?
Error Codes in your Maytag Top Load Washer:
Error code | Error |
---|---|
Ofb | The washer load is out of balance. |
OL | The washer load too large. |
PF | The wash cycle was interrupted by a power failure. |
Sud | There are excessive suds in washer. |
• 16 juin 2020
How do I reset my Maytag washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
How do I unlock my Maytag washer?
Maytag Front Load washer door locked at install
- The door may immediately unlock.
- The door lock LED light will blink. The door should unlock after 60 seconds. …
- The washer will go into a hold and drain routine for 8 minutes. After 8 minutes the door will unlock.
What does F5 mean on my washing machine?
The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range.
How do you bypass the clean cycle on a Maytag washer?
Hello Sandy, Press and hold the “Spin” and “Soil” button simultaneously for 10 seconds. A countdown will be displayed on the console. Once the countdown has completed the unit will have successfully reset.
What causes a Maytag washer not to spin?
One of the most common reasons for a Maytag top load washer not spinning is an incorrect wash cycle or spin setting. GENTLE, HANDWASH, or DELICATE settings utilize slower spin speeds for more fragile fabrics. Some model washers also allow you to vary the spin speed, making it slower or more rapid, for different loads.
What does the code CL mean on a Maytag washer?
Does the washer need to be cleaned? The CL code is a reminder to run the Clean Washer cycle and will appear after 30 cycles. The code will automatically clear once a Clean Washer cycle has completed or after three cycles.
Is there a recall on Maytag washers?
Important: CPSC Recall Remedy Notice Due to COVID-19
Description: The recall involves white Maytag front-load washers with model number MAH9700 and a serial number from 10188468GA through 11683946GJ. The model and serial numbers are located inside the door opening and below the rubber boot.
How do I run a clean cycle on a Maytag washer?
STEP 1: CLEAN THE TUB
- Remove any items left in the tub.
- Add an affresh® washing machine cleaner tablet to the bottom of the tub. …
- Close the door and select your washer’s cleaning cycle.
- For top load washers, when the cycle ends, run a rinse and spin cycle to clear away any excess cleansers.
Why is my Maytag washer not agitating?
If your washer won’t agitate but spins, a broken agitator may be to blame. … The output shaft of the transmission is splined to the agitator to secure it in place. Over time, some of the components of the agitator can wear down or break with normal usage, causing your washing machine not agitating issue.
How do you bypass the lock on a Maytag washer?
How do I unlock my Maytag washer?
- To unlock the controls, press and hold the CYCLE END SIGNAL for 3 deliberate seconds or until the control lock light goes out. …
- Press the “Drain and Spin” button on the washer’s control panel to attempt to unlock the machine.
How do I turn off the control lock on my Maytag washer?
To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.
How do you bypass the lid lock on a Maytag washer?
There is not anyway to bypass the lid switch on this model. the reason is the machine control is set up to do a child lock routine before it starts the cycle the washer will lock the lid then move the motor or spray water. Then will unlock and lock again before it starts the cycle.
What is F5 error code?
An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions.
Where is the filter on a Maytag top load washer?
The filter or trap is generally located inside the machine’s agitator. Its function is to capture lint and cast-off fibers.
How long is the normal cycle on a Maytag washer?
Best answer: The washer takes anywhere from 45 minutes to an hour to complete a cycle using the Normal Wash Cycle. Some other factors to consider is how long the machine takes to fill to do the laundry in the Normal Wash cycle and how much water pressure you have coming to the machine.
Why does my Maytag washer smell?
Wet laundry that sits in the Maytag washer for long periods may cause the machine to smell. Fungus and mildew thrive in moist environments; the dark, dank tub of wet laundry becomes the ideal breeding ground for bacteria and odors.
What causes a washing machine to not spin out?
An unbalanced load of laundry is one of the most common causes of an inadequate spin cycle. Sometimes clothing can settle on one side of the drum, throwing off the motion of the washing machine. … If you suspect a distribution problem, try rearranging your clumped-up wet laundry and running the spin cycle again.
How do I get my Maytag washer to spin only?
Actually you can have washer SPIN only. Choose “rinse & spin” then deselect the “extra rinse” button that lights up. It will SPIN ONLY!!
What does F5 and E3 mean on a washing machine?
The F5 E3 alert indicates there is issue with the lid lock. … Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. If this is unsuccessful, reboot the machine by unplugging the washer and wait two minutes before plugging the machine back in.