Maytag F/02 – Drain Cycle Too Long
The manufacturer has assigned this error or fault code to indicate that the washing machine drain cycle is taking too long. After 8 minutes of drain time the error code is displayed. … If the error code returns, check to be sure the drain hose isn’t clogged or kinked.
similarly, What does the code CL mean on a Maytag washer?
Does the washer need to be cleaned? The CL code is a reminder to run the Clean Washer cycle and will appear after 30 cycles. The code will automatically clear once a Clean Washer cycle has completed or after three cycles.
on the other hand, Can you reset a Maytag washing machine?
If an error message causes your Maytag washer to not run properly, reset the washer to clear the error message. You also can reset the washer if you want to cancel a setting you chose.
also, Is there a recall on Maytag washers? Important: CPSC Recall Remedy Notice Due to COVID-19
Description: The recall involves white Maytag front-load washers with model number MAH9700 and a serial number from 10188468GA through 11683946GJ. The model and serial numbers are located inside the door opening and below the rubber boot.
Why does my Maytag washer not start?
If your Maytag washing machine isn’t starting, verify that the power cord is connected to a live outlet. Test the outlet with another three-prong appliance. … Select a wash setting and pull out the knob to start the cycle. If it still won’t start, reset the circuit breaker or change out the fuses if they are blown.
How do I reset my Maytag washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
What does CL mean on my washing machine?
CL is not an error code, but an indicator that the child lock feature is active. When the child lock feature is active, the control panel is disabled, and settings cannot be adjusted. To activate or de-activate child lock, press and hold the child lock button for 3 seconds.
What does F5 and E3 mean on a washing machine?
The F5 E3 alert indicates there is issue with the lid lock. … Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. If this is unsuccessful, reboot the machine by unplugging the washer and wait two minutes before plugging the machine back in.
How do I reset my Maytag mvwx655dw1 washer?
Be sure the washer is in standby mode (plugged in with all indicators off). Perform the following sequence of movement using the cycle selector knob. NOTE: AFTER RESET, sequence “A” through “E” must be completed within 6 seconds. RESET – Rotate cycle selector knob counterclockwise one or more clicks to clear sequence.
How do you bypass the clean cycle on a Maytag washer?
Hello Sandy, Press and hold the “Spin” and “Soil” button simultaneously for 10 seconds. A countdown will be displayed on the console. Once the countdown has completed the unit will have successfully reset.
How long should a Maytag washer last?
Maytag & Whirlpool
Another manufacturer which expects their washing machines to last for 10 years. As long as you are cleaning the machine regularly and using the self-clean cycle, you can expect it to last long-er.
Which is better Maytag or Whirlpool washer?
Both brands will deliver a durable product and a quality clean. Maytag washing machines provide a greater value and display of features compared to Whirlpool, whereas with Whirlpool, you will find a greater selection of top-load and front-load products with a wider range of price points.
Has Maytag gone out of business?
The bid failed and Maytag was bought by Whirlpool for $1.7 billion. On April 1, 2006, Whirlpool completed its acquisition of Maytag Corporation. … The Maytag name would now be used on Whirlpool-designed appliances. Most Maytag employees were terminated, but some were offered jobs at Whirlpool.
How do you fix a washer that won’t start?
How to Fix a Washing Machine That Won’t Start
- Activate the power button.
- Test the outlet.
- Reset outlet if necessary.
- Make sure the power cord is plugged in.
- Check if fuses are blown or the circuit breaker is thrown.
- See if Delay Start has been pushed.
- See if Control Lock has been activated.
Why is my Maytag washer not filling up with water?
If the water inlet valve is defective, the wash may fill slowly or not fill at all. … If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.
Why is my washing machine not turning on?
Power Source
Make sure the machine is tightly plugged in. Next, check for a tripped circuit breaker. Reset the breaker and try to start the washer. If neither is at fault, you may have a damaged power cord.
Why is my Maytag washer not working?
When your washer isn’t working right, the solution may be as simple as switching up detergents, tightening a hose or leveling the appliance. … If you have a front load washer, a dirty drain pump filter can be a common cause of the issues listed below, like problems draining, spinning and odor.
How dO I turn off CHILD LOCK?
- You can activate the CHILD LOCK function by pressing the STOP button for more than 5 seconds. The key symbol will light up in the front panel display.
- To cancel, press the STOP button for more than 5 seconds so that the key symbol disappears from the front panel display.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
What does F5 mean on my washing machine?
The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range.
What does E3 mean on a Maytag washer?
The E3 error means that the control board is detecting current going to the motor, but the motor won’t turn properly. If the error code comes up all the time as soon as you press the power on button, then it means your control board is bad and reading incorrectly.
How do I fix F5 E3 error on Maytag washer?
F5 E3 Error Code
- Power unit down by turning off the circuit breaker or unplugging for one (1) minute.
- Power unit up by reconnecting power.
- Restart a new cycle.
- Monitor the washer for one (1) minute to ensure the error code does not display again.
How long is the normal cycle on a Maytag washer?
Best answer: The washer takes anywhere from 45 minutes to an hour to complete a cycle using the Normal Wash Cycle. Some other factors to consider is how long the machine takes to fill to do the laundry in the Normal Wash cycle and how much water pressure you have coming to the machine.
Why does my Maytag washer smell?
Wet laundry that sits in the Maytag washer for long periods may cause the machine to smell. Fungus and mildew thrive in moist environments; the dark, dank tub of wet laundry becomes the ideal breeding ground for bacteria and odors.
What is the power wash setting on Maytag washer?
PowerWash® Cycle – The PowerWash® cycle features a combination of more wash action and heated water to drive powerful cleaning. PowerWash® Agitator – The PowerWash® agitator tackles any load size with both efficient, concentrated cleaning to fight stubborn stains and robust wash action to help break up messes.
Don’t forget to share the post !