The F5 E3 alert indicates there is issue with the lid lock. … Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. If this is unsuccessful, reboot the machine by unplugging the washer and wait two minutes before plugging the machine back in.
Table of Contents
READ ALSO
Likewise, What does E3 mean on a Whirlpool dryer?
The Whirlpool Duet Dryer E3 Error means either the logic chip in the main control has failed or the user interface or main control board was replaced with the wrong part and is not compatible with that model.
Also, What does F5 E3 mean on a Whirlpool front load washer?
F5 E3 Error Code
Power unit down by turning off the circuit breaker or unplugging for one (1) minute. Power unit up by reconnecting power. Restart a new cycle. Monitor the washer for one (1) minute to ensure the error code does not display again.
Moreover, How do I fix F5 E3 error on Maytag washer?
F5 E3 Error Code
- Power unit down by turning off the circuit breaker or unplugging for one (1) minute.
- Power unit up by reconnecting power.
- Restart a new cycle.
- Monitor the washer for one (1) minute to ensure the error code does not display again.
Why does my washer keep saying F5?
A temperature sensor resistance that is out of the normal range is detected by the Central Control Unit. A failed NTC temperature sensor is what causes the F5 error.
Where is the error code on a Whirlpool Duet dryer?
Unplug the dryer for 5 minutes and then plug it in. If the code returns, replace the main electronic control board. A button is stuck on the keypad on one of the two user interface control assemblies in the console. If you can’t free the button, replace the user interface control assembly with the stuck button.
What does F3 mean on dryer?
The “F3” fault code is displayed because the dryer is not heating. The first thing to check and verify is the voltage supply. The dryer must have 220 volts or it will run but not heat. If the dryer is getting the correct voltage then I would disconnect the power cord and then remove the top panel.
How do I reset my Whirlpool Duet dryer?
Resetting your Whirlpool Duet Dryer is very easy. All you have to do is turn it off and unplug it. Keep the dryer unplugged for at least one minute, plug it back in, then switch it on to finish the process.
What does F5 and E2 mean on a washing machine?
The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.
How do you unlock a Whirlpool front load washer?
Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.
How do you reset a Whirlpool washing machine?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
What does E3 F6 mean on Maytag washer?
The F6 E3 alert indicates there is issue with the appliance control unit, user interface or associated wiring. Unplug the washer, wait five minutes, then plug back in.
How do I fix the lid lock on my Whirlpool washer?
Follow these steps to perform a Whirlpool washer lid lock bypass:
- Unplug the washer and move it away from the wall.
- Remove the top panel by pushing in its retaining tabs or removing its screws.
- Locate the lid lock switch underneath the top panel.
- Secure a strong magnet between the switch and the panel.
How do you run a diagnostic on a Whirlpool Duet washer?
Duet Washer Diagnostic Test Mode
Pick any three buttons on the Duet washer control except power, start, or cancel. Now do the key dance within eight seconds… Button 1, Button 2, Button 3, Button 1, Button 2, Button 3, Button 1, Button 2, Button 3 (You are pressing 9 buttons in 8 seconds so it needs to be pretty quick.)
What does the code F01 mean on a Whirlpool Duet dryer?
Troubleshooting and Repair – F01 Error Code – WED8300SW0. The F01 error code means the primary control unit in the dryer has failed and will have to be replaced. The control that needs replacing is the electronic control board not the user interface and/or control panel.
How do I read a whirlpool error code?
Error Codes in my Whirlpool Front Load Washer
| Error Code | Error |
|---|---|
| Sud or Sd | There are too many suds in the washing machine. |
| F5 E2 | The door is not locking properly. |
| F7 E1 | Indicates a motor speed sensing error, |
| F8 E1 or LO FL | The washer is sensing a low flow of water. |
• 15 juin 2020
How do you reset a Whirlpool front load dryer?
If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.
Why does my Whirlpool dryer not start?
Sometimes a Whirlpool dryer not starting is more of a power issue than a dryer malfunction. … Make sure the dryer is correctly plugged into the proper electrical outlet. Check for tripped breakers or blown fuses. If needed, reset any tripped breakers and replace blown fuses.
How do I fix E2 error on my Whirlpool washer?
F5 E2 Error Code
- Power unit down by turning off the circuit breaker or unplugging for one (1) minute.
- Power unit up by reconnecting power.
- Open and close the door.
- Restart a new cycle.
- Monitor the washer for one (1) minute to ensure the error code does not display again.
What does E2 mean on my washing machine?
The E2 error in Samsung washing machines informs the user about water draining problems. For some reasons, the device can’t drain the waste of water. Besides, it can report about unhurried discharge. So waiting time for draining is exceeded.
What does E2 mean on a Whirlpool washing machine?
The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way. CLICK HERE to review a video for more information on the F5 E2 code.
How do you bypass the lock on a Whirlpool washer?
Follow these steps to perform a Whirlpool washer lid lock bypass:
- Unplug the washer and move it away from the wall.
- Remove the top panel by pushing in its retaining tabs or removing its screws.
- Locate the lid lock switch underneath the top panel.
- Secure a strong magnet between the switch and the panel.
Why is my Whirlpool washer stuck on sensing?
A blinking sensing light indicates an underlying issue with the drain, spin, or any other function. There are several such problems that Whirlpool washers commonly run into. … The washer will function only when the lid/door is completely closed. The water pump belt in the washer has worn out or is damaged.
How do I unlock my front load washer door?
Opening a Manual Lock. Turn the washing machine off and unplug it. If you’re in the middle of a cycle, turn the dial or press the button to pause or end the cycle. Wait 5-6 seconds to see if the door unlocks.
