The F5 E3 alert indicates there is issue with the lid lock. … Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. If this is unsuccessful, reboot the machine by unplugging the washer and wait two minutes before plugging the machine back in.
Table of Contents
READ ALSO
Likewise, What does F5 E3 mean on a Whirlpool front load washer?
The F5 E3 alert indicates there is issue with the lid lock. Do not force the lid open, as permanent damage could occur. Remove any objects from the lid and clear any obstructions.
Also, How do I fix F5 E3 error on Maytag washer?
F5 E3 Error Code
- Power unit down by turning off the circuit breaker or unplugging for one (1) minute.
- Power unit up by reconnecting power.
- Restart a new cycle.
- Monitor the washer for one (1) minute to ensure the error code does not display again.
Moreover, What does E3 mean on a Whirlpool dryer?
The Whirlpool Duet Dryer E3 Error means either the logic chip in the main control has failed or the user interface or main control board was replaced with the wrong part and is not compatible with that model.
Why does my washer keep saying F5?
A temperature sensor resistance that is out of the normal range is detected by the Central Control Unit. A failed NTC temperature sensor is what causes the F5 error.
What does F5 and E2 mean on a washing machine?
The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.
How do you unlock a Whirlpool front load washer?
Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.
What does E3 F6 mean on Maytag washer?
The F6 E3 alert indicates there is issue with the appliance control unit, user interface or associated wiring. Unplug the washer, wait five minutes, then plug back in.
How do you reset a Whirlpool washing machine?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
Where is the error code on a Whirlpool Duet dryer?
Unplug the dryer for 5 minutes and then plug it in. If the code returns, replace the main electronic control board. A button is stuck on the keypad on one of the two user interface control assemblies in the console. If you can’t free the button, replace the user interface control assembly with the stuck button.
What does F3 mean on dryer?
The “F3” fault code is displayed because the dryer is not heating. The first thing to check and verify is the voltage supply. The dryer must have 220 volts or it will run but not heat. If the dryer is getting the correct voltage then I would disconnect the power cord and then remove the top panel.
How do I reset my Whirlpool Duet dryer?
Resetting your Whirlpool Duet Dryer is very easy. All you have to do is turn it off and unplug it. Keep the dryer unplugged for at least one minute, plug it back in, then switch it on to finish the process.
How do I fix the lid lock on my Whirlpool washer?
Follow these steps to perform a Whirlpool washer lid lock bypass:
- Unplug the washer and move it away from the wall.
- Remove the top panel by pushing in its retaining tabs or removing its screws.
- Locate the lid lock switch underneath the top panel.
- Secure a strong magnet between the switch and the panel.
How do I fix E2 error on my Whirlpool washer?
F5 E2 Error Code
- Power unit down by turning off the circuit breaker or unplugging for one (1) minute.
- Power unit up by reconnecting power.
- Open and close the door.
- Restart a new cycle.
- Monitor the washer for one (1) minute to ensure the error code does not display again.
What does E2 mean on my washing machine?
The E2 error in Samsung washing machines informs the user about water draining problems. For some reasons, the device can’t drain the waste of water. Besides, it can report about unhurried discharge. So waiting time for draining is exceeded.
What does E2 mean on a Whirlpool washing machine?
The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way. CLICK HERE to review a video for more information on the F5 E2 code.
How do you bypass the lock on a Whirlpool washer?
Follow these steps to perform a Whirlpool washer lid lock bypass:
- Unplug the washer and move it away from the wall.
- Remove the top panel by pushing in its retaining tabs or removing its screws.
- Locate the lid lock switch underneath the top panel.
- Secure a strong magnet between the switch and the panel.
Why is my Whirlpool washer stuck on sensing?
A blinking sensing light indicates an underlying issue with the drain, spin, or any other function. There are several such problems that Whirlpool washers commonly run into. … The washer will function only when the lid/door is completely closed. The water pump belt in the washer has worn out or is damaged.
How do I unlock my front load washer door?
Opening a Manual Lock. Turn the washing machine off and unplug it. If you’re in the middle of a cycle, turn the dial or press the button to pause or end the cycle. Wait 5-6 seconds to see if the door unlocks.
What does F6 and E3 mean on a Whirlpool washer?
The Whirlpool washer F6E3 error code is a communication error from the ACU ( main control board) to the UI ( User interface ). This error is most times caused by faulty wiring or loose connectors at one the boards. It can also be caused by either board having failed.
What does F6 mean on a Whirlpool washing machine?
The F6 error code for this model indicates a drive motor tachometer error. The control board is unable to properly detect the motor speed. If you have a volt/ohm meter I can give you a few checks that will help you diagnose the problem.
How do I clear the error code on my Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Do Whirlpool washers have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
