The error message is caused by opening the microwave door too early when you are using the sensor cooking function. Removing the error message from the microwave display takes only a moment.
Table of Contents
READ ALSO
Likewise, How do I troubleshoot my Samsung microwave?
Samsung microwave is not heating or has stopped working
- Verify that the microwave is not in Demo mode. …
- Check the Kitchen Timer feature. …
- Inspect the door. …
- Verify there is enough clearance on all sides. …
- Request service.
Also, What do you do when your microwave says error?
Indication of an issue with the electronic control in the microwave. Sometimes shutting off the circuit breaker or fuse that supplies power to the microwave oven for 30 seconds will clear the fault, error or function code.
Moreover, What does E 10 mean in microwave?
First, error E10 means that your display control board itself has an internal short detected. You can try to unplug the microwave for 5 minutes to see if the electronics will reset but if that doesn’t work, the entire display board would need to be replaced.
Is there a fuse in a Samsung microwave?
The thermal fuse cuts off power to the microwave if the microwave overheats. To determine if the thermal fuse has blown, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it. The thermal fuse cannot be reset—if the fuse is blown, it must be replaced.
Why is my Samsung microwave not starting?
If your microwave is not turning on, or if it is turning off by itself, it could have overheated. When a microwave has been in use for a long time and overheats, just give it 30 minutes to cool off and then try to use it again. Otherwise, you’ll need to check the light, the outlet, and the power cord.
Is there a recall on Samsung microwaves?
announced a voluntary recall of approximately 43,000 Samsung over-the-range microwave ovens, citing a potential shock hazard. … The recall affects all Samsung 1000-watt over-the-range microwave ovens with the following model and serial numbers: SMH9151x from serial number xxxxxxxS1xxxxxx to xxxxxxxS5xxxxxx.
How do I reset my microwave?
Here’s how to reset a microwave via hard reset.
- Locate the plug of the microwave and pull that plug out of the socket.
- Wait for two to three minutes before plugging in the microwave.
- Turn on the microwave and set the time of the day by pressing the Clock button. Press the dial to enter the time, minutes, and the am/pm.
What does E 83 mean on a Samsung microwave?
E83 means that your control board has either failed or one of the door switches inside the microwave has failed. There are 3 door switches that you’ll need to test with a multimeter to see if one has failed.
Why does my microwave say f4?
The F-4 indicates a failure in the humidity sensor in the microwave. This is normally caused by a failed sensor. In rare instances, it can be caused by a failed control board. Since this is an internal microwave component failure, I recommend calling a service technician to diagnose and repair the microwave.
What does 1S mean on microwave?
The “1S” and “2S” normally mean “one stage” and “two stage” cooking.
How do you know if your microwave fuse is blown?
It’s easy to tell if a glass fuse is blown; it will show scorch marks, and the filament will be melted. To check a ceramic fuse, use an ohmmeter or continuity tester. With an ohmmeter or multimeter, you should see a reading close to zero ohms if the fuse is intact, or infinite if it’s blown.
What causes a microwave to suddenly stop working?
The most common cause for a microwave oven not working at all is a blown main fuse. The microwave main fuse will cut the flow of electricity if too much current passes through it. … There can also be thermal fuses, cavity fuses, and thermoprotectors which will interrupt the electrical flow if the microwave overheats.
Does a microwave have a reset button?
Does a Microwave Have a Reset Button? Most microwave ovens do not include a reset button. … A hard reset happens when you physically unplug the microwaves’ cord from the wall outlet.
How long do Samsung microwaves last?
The average microwave oven lasts about seven years with normal use, and even less with heavy use and poor maintenance.
What can cause a microwave to stop working?
The most common cause for a microwave oven not working at all is a blown main fuse. The microwave main fuse will cut the flow of electricity if too much current passes through it. … There can also be thermal fuses, cavity fuses, and thermoprotectors which will interrupt the electrical flow if the microwave overheats.
Why does my Samsung microwave keep shutting off?
If the Microwave is overheating and shutting itself down, this is caused by high voltage parts inside the unit getting too hot the leading the thermal cut-out switch to be activated as a safe feature to prevent further overheating.
Is there a reset button on microwaves?
Does a Microwave Have a Reset Button? Most microwave ovens do not include a reset button. … A hard reset happens when you physically unplug the microwaves’ cord from the wall outlet.
What is a hard reset on a microwave?
A hard reset is necessary. Take the plug out of the wall power supply. The microwave’s memory can be reset by plugging the microwave back into the wall power supply. If you perform a hard reset, you’ll need to change the time of day.
What does E1 mean on a microwave?
Microwaves , Wall Ovens , Whirlpool , Appliances. 1 Answer from this member: The “E1 F1” fault code indicates an Electronic control board malfunction. This means that the control board will need to replaced.
How do I reset my Samsung range?
How to reset an electric stove?
- Press the Cancel / Off button repeatedly until the LCD screen shows the clock.
- Press Cancel / Off until the LCD screen and oven turn off.
- Unplug the oven from the power outlet or switch and wait 60 seconds.
What does se mean on microwave?
The SE error code means the microwave has had a Key short error. The control panel or smart board will need to be replaced.
What does F3 mean on microwave?
The F3 means you have a shorting membrane keypad. If and when an oven exhibits this code or is coming on or doing anything by itself, this is very dangerous and can result in a fire. None of us on this site recommend trying to repair this type of problem on a microwave because it can kill you.
Why does my microwave keep saying food?
The “FOOD” or “Insert Food” message on the display means the microwave thinks food has not been added yet. To correct the issue, open and close the door again and press “START.”
