An IE error code indicates that the washer was unable to fill with water. During cold and freezing weather conditions, an IE error code could mean the water in the water supply lines are frozen.
Table of Contents
READ ALSO
Likewise, Why is my LG washer flashing Le?
An LE error code on the washer’s display indicates that the motor is locked, possibly due to a heavy wash load. Large and heavy sized loads will put a strain on the motor, causing the LE code to occur. Performing a reset on the washer will normally resolve this error with a reduced load size.
Also, How do I fix OE error on my LG top load washer?
Force drain the unit by starting a cycle and pausing it.
…
If you don’t have SPIN ONLY
- Power the unit ON.
- Select a cycle.
- Press START/PAUSE button to START the cycle.
- Allow a few minutes to pass so the cycle begins.
- Press the START/PAUSE button to PAUSE the cycle.
- Run an empty wash cycle to see if issue occurs again.
Moreover, Why does my LG washer keep filling with water?
If the washer continues to fill with water even when it is not getting power, this indicates that the water inlet valve is defective. If the water inlet valve is defective, replace it. … If the pressure switch fails, the water inlet valve will continue to fill the washer tub with water, causing the washer to overflow.
Why is my LG washer not getting water?
Common solutions for: LG Washer fills slowly or will not fill at all. The water inlet valve opens to allow water to enter the washing machine. … If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.
How do I test my LG washing machine drain pump?
Test the drain pump.
- Press POWER to turn the washer ON.
- Press the SPIN SPEED key until HIGH is selected.
- Press the START/PAUSE button to start the SPIN ONLY cycle.
- Listen to hear a humming sound which indicates that the drain pump motor has started working.
How do I know if my inlet valve is bad?
Signs that point to an inlet valve problem include leaks that fill the dishwasher when not running, the dishwasher filling too slowly when in use, or the dishwasher not filling at all. Leaks that end up outside of the dishwasher also can indicate an inlet valve problem, and this must be addressed immediately.
Why is my washer filling up and draining at the same time?
If your washer continues to fill during a drain cycle, the water inlet valve could be at fault. … If the washer continues to fill, then the inlet valve is defective. If the washer stops filling, then the problem is related to the electrical circuit that controls the valve.
How do I troubleshoot my LG washer?
How to Troubleshoot LG Washer Problems
- Adjust your clothes. …
- Check the drum and drain filter for foreign objects. …
- Adjust the leveling feet at the base of your LG washer. …
- Check your hoses. …
- Check the power. …
- Contact LG customer support, if none of the previous steps help.
How do I use the water plus feature on my LG washer?
To use the Water Plus function:
- Pause the washer during the wash or rinse cycle once the. washer has stopped filling. ( Water Plus is not available. during the spin cycle.)
- Touch the Change Settings button.
- Select Water Plus from the Cycle Settings screen.
- Touch the Start button to resume the cycle.
How long does LG washer last?
The average life expectancy for washers and dryers is between 10 and 15 years. Front loaders are very efficient.
How do I know if my washing machine pump is clogged?
Check the pump
Sometimes, it’s as simple as a lost coin blocking the pump. Behind the machine’s service hatch you’ll usually see a round access cap about the size of a biscuit – put the tray under it to catch any water, then carefully unscrew and remove it. This will reveal the pump’s impeller.
Can you clean a water inlet valve?
Washing machines pull in water from your home’s water supply and mix it with detergent in the laundry tub. … It is a good idea to clean the water inlet valve on your washing machine every year or so.
Can you repair water inlet valve?
There is little that you can do to repair the valve itself, but you can clean the two inlet ports to restore full water flow. You can also test the valve to determine whether it has failed. Replacing a bad valve is a simple job and must be done with parts and procedures that are specific to your washing machine model.
How much does a water inlet valve cost?
Machine Inlet Valve Repair
The washing machine inlet valve connects the hoses needed for the unit to fill with water. Signs of a faulty inlet valve is that no water or only a small amount of water is filling the tub. A washing machine inlet valve replacement costs $75 to $125.
How do I know if my washing machine drain pump is bad?
Put your finger into the drain outlet and feel the impellers if the pump freely turns. One or more of them may be broken. If so, you’ll be able to feel them while you’re turning the pump flywheel with your other hand. You also may see broken pieces of plastic in the bottom of the pump housing.
What causes a washer to keep filling?
Water Pressure
One of the less common reasons your washer may be overfilling is that there is not enough water pressure for the water inlet valve to work correctly. If there is not enough water pressure, the water inlet valve will not close completely, which can cause the washer to overfill.
Why is my washer not holding water?
Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed. Whatever the reason, the water will need to be drained from the washing machine before any work or diagnosis can be done.
Are there any recalls on LG washers?
Incidents/Injuries: LG has received at least 343 reports of washing machines vibrating excessively, of which at least 187 involved minor property damage. … Consumers who have observed their recalled washing machine shaking excessively should immediately stop using it.
Do washing machines have a reset button?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
What is Turbo wash on LG washer?
LG’s TurboWash™ 360 technology is a technology that allows you to power-clean big loads of laundry in less than 30 minutes and still get the same kind of washing performance as longer cycles on the ENERGY STAR® Qualified LG 4.5 cu.ft.
What does deep wash mean on LG washer?
Deep wash means extra water hope that worked for you. … deep wash should put extra water in the tub but it depends on the weight of your load size if it will completely cover the fabric. heavy duty wash might be a better cycle to get your fabric clean. more water doesnt mean a cleaner wash. more action in the wash does.
What is fresh care setting on LG washer?
The Fresh Care option will tumble finished loads of wet laundry for up to 19 hours to keep it from getting musty.
