By Lyle Weischwill. A dc error code on your Samsung front-load washer means the washer won’t spin because the load is unbalanced. Fixing a dc error code can be as easy as redistributing an unbalanced load or adding a few garments to a small or single-item load.
similarly, What do you do if your Samsung washer won’t drain?
More videos on YouTube
- Turn off the washer and check the level. If the washer isn’t level it may not drain correctly. …
- Inspect the drain hose. …
- Clean the pump filter (front loaders only). …
- Turn the washer back on and start a cycle.
on the other hand, How do I get my Samsung washer to spin only?
To run a Spin Only cycle on a model that does not have this option on the cycle selector dial, perform the following:
- Power the unit on.
- Press and hold the spin key for approximately 3 seconds. A chime will sound.
- Select the spin level, if desired.
- Press the Start/Pause button.
also, Why is my Samsung washer always unbalanced? The drum is overloaded or underloaded. If you wash your laundry at a temperature of more than 60 degrees, some extra water enters the washer during the rinse cycle. This may lead to a slight imbalance. … If the bearings are worn or rusty or the shaft is bent, the vibration increases and the washer may not spin at all.
How do I force drain my Samsung washer?
[Solution]
- 1 Unplug the washing machine from the power supply.
- 2 Open the filter-cover.
- 3 Unscrew the emergency drain cap by turning it to the left.
- 4 Grip the cap on the end of the emergency drain tube, and then slowly pull it out about 15 cm (about 6 inches).
- 5 Allow all the water to flow into a bowl.
How do I get my washer to spin only?
- To perform a spin only cycle: Press the power button to turn the washer on. Press and hold the spin button for 3 seconds. …
- Yes, hold spin only at center bottom of key pad. Has asterisk next to it. …
- Press spécial care then spin only. …
- Spin towels. …
- Press on then special care then spin only. …
- Just put it on spin, and it will.
Why is my washer not spinning all the water out of my clothes?
Drain Hose Issues
The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. It could be clogged, kinked, or even positioned incorrectly if you had to remove the drain tube to make another repair already.
How do I force my Samsung washer to drain?
[Solution]
- 1 Unplug the washing machine from the power supply.
- 2 Open the filter-cover.
- 3 Unscrew the emergency drain cap by turning it to the left.
- 4 Grip the cap on the end of the emergency drain tube, and then slowly pull it out about 15 cm (about 6 inches).
- 5 Allow all the water to flow into a bowl.
Why does my washer get unbalanced?
If a suspension rod is broken, replace it. One or more of the suspension springs might be broken. The suspension springs help to absorb the movement of the washer tub. If a suspension spring breaks, the tub might become unbalanced, causing it to shake and vibrate during operation.
Why does my washer keep getting off balance?
Check that the machine is level across the front, back and sides. A machine that is not level will rock during the spin cycle and cause the machine to be off balance. All four legs should be in firm contact with a solid floor. A carpeted surface can throw this balance off.
Does Spin Cycle drain water?
It removes the water from the tub during the spin cycle. The washer pump forces water from the bottom of the machine into the drain hose. The drain hose loops to the top of the machine, and then down to the drain, enabling the tub to fill. When the water reaches the bend in the hose, it goes out of the drain.
Why Samsung washer will not drain?
If the water pump belt is broken or worn out, the washer will not drain. … First, check the drain hose to determine if it is kinked, twisted, or bent. If the drain hose is bent, straighten it out. In addition, remove the drain hose and check it for obstructions.
Where is the filter on a Samsung top loader washing machine?
Have a look at the bottom part of the front panel of the washer. Open it using a flathead screwdriver, because some laches may secure it. After removing the panel, you will see the filter – a plastic part with a shaped inbuilt handle.
Why does my Samsung washing machine not spin?
If your Samsung washing machine does not spin fully or at all during the rinsing or spinning phase of the cycle it is most likely to be caused by an unbalanced load. … 1 Open the door and redistribute the washing more evenly around the drum. 2 Check that the drum is not over or under loaded.
How do you force a GE washer to drain?
There may be a clog.
- Press Start to resume the cycle or you can select Drain & Spin and press Start. …
- If water remains in the washer, check for a pinched or flattened drain hose. …
- If you clear a clog, press START to resume your cycle or you can select Drain & Spin and press Start.
Why does drain and spin fill with water?
Basically, it pours water from the top while draining it out from the bottom. It drains the water faster than it can pour it, so it does not actually fill with water, but it does re-wet the clothes, so the clothes are dripping wet when the cycle is complete.
How do you get excess water out of clothes?
Roll the towel to squeeze more water out of the clothing.
Roll the towel over and onto the clothing. Gently press down on the towel roll to squeeze as much water as possible out of the garment. If the towel becomes soaked, unroll it. Roll the clothing up in a different towel and squeeze out the remaining water.
Is it okay to put soaking wet clothes in the dryer?
Here’s What You Should Know. Your clothes washer is designed to drain and spin at the end of each load so that your clothes are only damp when you put them in the dryer. If clothes are coming out of the washer soaking wet, it’s a sure sign of a problem.
Why is my Samsung front loader not draining?
If your front load Samsung washer won’t drain, the drain pump filter may be clogged. In front-loading machines, this filter prevents small articles of clothing and debris from damaging the drain pump. However, if it gets clogged, the washer may not drain properly.
How do you balance an unbalanced washing machine?
Top-loading washers automatically adjust to level. If something has shifted, you can relevel a top-loading washer by tipping the washer forward, then placing it back on the floor. Front-loading washers level by turning a leg to raise or lower it.
How do I know if my washer is off balance?
If your washer has started making loud noises and vibrating excessively during the washer cycle, it can be a sign that something is wrong. However, both these symptoms can also be caused by something much simpler – an out of balance washing machine.
How often should you drain your washing machine?
Washing machines can be breeding grounds for salmonella and other germs. When you wash items in hot water, your machine is being cleaned as well, but once a month, you should still run an empty load with hot water and about a cup of distilled white vinegar to sanitize the basin and wipe out any lingering germs.
Why are my clothes too wet after the spin cycle?
Loading Too Many Items
Overloading can lead to an imbalance that reduces the washer’s spin speed, leaving clothes too wet after spin cycle completes. If the washer leaves clothes soaked after a large load, remove some items, redistribute others and run another rinse and spin cycle.
Does drain and spin wash clothes?
It rinses the clothing with clean water and then spins at a fast speed to remove any moisture from the load. … This setting can be used after a wash to, remove excess water, however the clothing will not be fully dry. – Drain. This programme is intended to drain the machine of water.
Don’t forget to share the post !