Rinnai fault code 11 – No ignition. Check to make sure the gas is turned on at the water heater, gas meter or tank. Ensure the igniter is operational. … Make sure the heat exchanger is not clogged and that low water flow is not causing short cycling.
similarly, How do I fix error code 79 on Rinnai?
Error Code 79
- Inspect the wiring harness on the leak detector. …
- Inspect the heat exchanger and all the internal piping within the tankless. …
- If you don’t find any leakage, look inside the cabinet. …
- If you find evidence of water pooling, dry off the leak sensor as well as the inside of the cabinet.
on the other hand, How do I fix noritz Error 11?
How to Troubleshoot a Noritz Code 11
- Find the gas valve connected to the Noritz water heater and turn the gas valve counterclockwise until it no longer turns to open it completely.
- Turn the power off to the unit by pressing the “Power” button. Run hot water from a nearby faucet. …
- Turn the hot water back off.
also, How do you test a Rinnai Ignitor? Igniter issues
Test the unit’s igniter for proper work by cycling the unit and checking if there is a spark. If there is no spark, look for the loose, bad, or no connection and the damaged element. Verify the correct voltage on the electric board when the unit is in the ignition cycle.
Why does my Rinnai gas heater keep turning off?
The main reasons that a gas water heater automatically shuts off are because the pilot light goes out, the pilot light can’t start, or there are problems with the gas supply. If your gas water heater keeps shutting off, the thermocouple could be dirty, bent or damaged.
How do I get Rinnai error codes?
If your water heater is connected to MC-91 or MCC-91, you can easily find the most recent error codes. Press and hold the ON/OFF button for two seconds and press the arrow “UP”, the last nine Rinnai error codes will appear and flash one after the other.
How do I fix my Rinnai Code 65?
You can attempt to clear any Rinnai error code yourself by turning your hot water tap off and on again, and by pushing the on/off button on your monitor off, then on again. If the fault code remains then further action will be required to rectify the issue.
Why is my Rinnai water heater not working?
Check the water supply and ensure the water flow is at least 30 psi. Check the pump wiring, look for any loose, damaged, or broken connections, and replace if necessary. Drain the water tank and check the water inlet filter for any blockages. If it is clogged, clean it or replace it.
How do I fix noritz Error Code 45?
To fix error code 45, you may need to have a licensed contractor assess the condition of your Noritz tankless water heater. If there are no visible signs of water or moisture, reset the unit by switching it off for at least 30 seconds. If the error code shows again after the reset, you will have to call for service.
Why is my Rinnai beeping?
Your tankless water heater will “beep” and display an error code to alert you to a problem with the system. Tankless water heaters will alert you with an audible alarm when service is required, a component fails, or a gas or water leak is present.
How do I fix error code 12 on Rinnai?
If you encounter error code 12, you can try the following steps to fix the problem:
- Check gas is turned on at the gas metre or cylinder.
- Check gas is turned on at the water heater.
- Check there are no obstructions to the flue outlet.
Why is my gas heater keep shutting off?
If your furnace shuts off too often, you could have a corroded or dirty flame sensor. A flame sensor lets your system know there’s a flame when the gas valve is open. If there isn’t a flame, the sensor will shut off the gas valve to keep the gas from getting into your house.
How do I know if my flame sensor is bad?
Signs of a bad furnace flame sensor are:
- The furnace lights but then shuts down after a few seconds (short cycles)
- The porcelain on the flame sensor is cracked.
- The flame sensor is sooty or corroded.
How do I fix my Rinnai Code 19?
Rinnai error code 19 signifies that there is a problem with the electrical grounding. To fix the Rinnai error code 19, inspect all electrical components of the unit for electrical shorts.
How do I fix my Rinnai Code 25?
Rinnai Error 25 Fix
- Turn off your hot water system.
- Locate your system’s condensate line.
- Inspect the line and remove any blockages.
- Check the condensate trap.
- Turn on your hot water system and see if the error code has gone.
How do I fix my Rinnai Code 12?
If you encounter error code 12, you can try the following steps to fix the problem:
- Check gas is turned on at the gas metre or cylinder.
- Check gas is turned on at the water heater.
- Check there are no obstructions to the flue outlet.
How do you test a Rinnai Ignitor?
Igniter issues
Test the unit’s igniter for proper work by cycling the unit and checking if there is a spark. If there is no spark, look for the loose, bad, or no connection and the damaged element. Verify the correct voltage on the electric board when the unit is in the ignition cycle.
How does Rinnai recirculation work?
Wireless Motion Sensor
Mounted near the point of use, the motion sensor operates the recirculation system by detecting full-body movement up to 30 feet away.
What is the priority button on Rinnai?
1. Press the “Priority button” on the temperature controller. The Priority light will glow indicating that this controller is controlling the temperature and that the Rinnai water heater is ready to supply hot water.
How do I reset my Rinnai WIFI module?
How To Factory Reset – Press and hold the Connect button (see below) on the module until the LED blinks WHITE, and then release. The module will reboot and the module LED turns solid RED when complete.
How long does a Rinnai water heater last?
The life expectancy (or useful lifespan) of a Rinnai tankless water heater is up to 20 years. Actual life is impacted by water quality, usage and proper maintenance. For comparison, a tankless water heater lasts about twice as long as a tank water heater, making them a better value in the long run.
Is there a reset button on a tankless water heater?
To prevent accidental resets, tankless water heaters are designed to prevent accidental resets, so you are probably going to have to hold the button down to get the reset to trigger.
How do I fix noritz error code F76?
Error Code F76
Solution: Disconnect the power to reset the unit and make sure that the connecting cord is not damaged.
How do I reset my tankless water heater?
How do you reset a tankless gas water heater ?
- Locate the red reset button. There should be a red button in the center of the control panel.
- Press the button firmly. The reset button can sometimes be sticky, especially if you haven’t reset the heater in a while.
- Wait to hear the button click.
Don’t forget to share the post !
