Error E21 usually means excess water left in condenser or condenser pump not working/pumping to the reservoir. This can be due to wet condenser and/or blocked/faulty pump. Unplug the appliance and remove the condenser, clean the area and let the condenser dry for a while. Then plug it back after around 30 minutes.
Table of Contents
READ ALSO
similarly, How do I know if my washing machine pump is clogged?
Check the pump
Sometimes, it’s as simple as a lost coin blocking the pump. Behind the machine’s service hatch you’ll usually see a round access cap about the size of a biscuit – put the tray under it to catch any water, then carefully unscrew and remove it. This will reveal the pump’s impeller.
on the other hand, What does error code E20 mean?
With an error message E20, your AEG washing machine doesn’t drain the water. The drum may be full of water. This may be due to a clogged drain filter or another problem with the drain. Open the flap at the front of the washing machine at the bottom right.
also, What is an E20 error? Washer dryer displays error message E20 or C2, emits 2 beeps or 2 flashes. It indicates pumping problems. Washer dryer does not drain. The drum does not turn. The appliance makes an unusual noise because of the blockage of the drain pump.
Where is the drain pump on a washing machine?
The drain pump is located at the bottom of your washing machine, but can be easily accessed in order to replace it if need be. If your washing machine is failing to drain during a wash cycle, it could be that there is a problem with the drain pump.
How do you know if your washing machine drain hose is clogged?
An easy way to check that the drain hose is clear is to blow air through it. If nothing is obstructing the drain tube, the problem is most likely at the washing machine pump. If the hose is worn or badly kinked, replacing the hose may improve the ability of the machine to pump water.
How do I fix EFO errors?
EF0 or EF3 warning message on the display can have several causes. When a lot of soap powder is used or a lot of foam is produced, the level system can get blocked by foam. You can fix this by switching off the machine and shaking the drum forwards and backwards several times.
Why does E20 keep coming up on my washing machine?
On some models an obstruction or blockage in the drain pump may cause E20 to appear in the display. … On some models an obstruction or blockage in the drain pump may cause E20 to appear in the display. Please watch our video clip to show you how to check for and remove any blockages from the drain pump.
What does Error E20 mean on Hoover washing machine?
E20 is “A problem with water draining” Solutions: The drain hose may be squashed or kinked. the drain pump may be blocked. or possible your filter is totally blocked.
Why is washer not draining water?
There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
How do I clear a clogged washing machine drain?
To unclog a clogged drain, first fill a bucket with boiling water and a pack of baking soda. Remove the drain pipe from your washing machine and slowly pour the water into the drain using a funnel. Wait a few minutes and test if it keeps draining if you pour water into it.
How much does it cost to replace a washing machine drain pump?
Washing machine pump 2 repairs are usually required when you note active leaks or a tub that doesn’t drain. If a pump is no longer working, it’s a relatively easy fix for a contractor and extends the lifetime of your appliance. On average, expect to spend $300 to $400 for a pump replacement job.
What is the best drain cleaner for washing machine drain?
Here is a List of the Best Drain Cleaners
- Instant Power Hair and Grease Drain Opener. …
- Thrift Drain Cleaner. …
- Roebic K-87 Soap, Grease, and Paper Digester. …
- FlexiSnake Drain Weasel Sink Snake. …
- Omont Drain Snake Clog Remover. …
- Vastar Drain Snake Hair Drain Clog Remover. …
- FlexiSnake Drain Millipede Hair Clog Tool.
Can a clogged filter cause a washing machine to leak?
Whilst a blockage is more likely to result in the water being unable to drain from the appliance, rather than a leak, leaks can occur from the filter if the seal becomes damaged. You can check this by removing the filter and giving the seal a once over, replacing it if it appears damaged.
What does EFO mean on washing machine?
: The error code. EF0. displays due to washer over-sudsing or due to washer not filling with. Hot. water.
How do I fix EFO error on my AEG washing machine?
Resolution:
- Use less detergent. Using too much detergent may cause excessive foaming. …
- Clean the dispenser drawer. …
- Check for laundry caught in the machine. …
- Check for leaking at the bottom – fluff filter. …
- Check the water supply hose. …
- Check the door seal. …
- Contact an Authorized Service Center.
How do you reset a Bosch washing machine?
How to reset an error code on a washing machine by Bosch, Neff, or Siemens. Press and hold down on the spin button and simultaneously turn the dial to the 7 o’clock position. Hold the spin button for around 5 seconds and then release.
Why is my washing machine saying error?
Common appliance codes could be related to a problem with the door, a water heating sensor, a software or circuit board fault, a motor or pump fault plus much more. Simple things that could have an error code could be the door being left ajar on the machine or the detergent drawer not in situ properly.
How do you fix an E20 error on a Hoover washing machine?
You can fix this by switching off the machine and shaking the drum forwards and backwards several times. Clean the drain pump/filter and then run a hot wash without any soap powder. 8. Switch off the power to the washing machine.
How do you drain a washer that won’t drain?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
How do I get the water out of my washing machine that won’t drain?
5 Easy Steps to Get Water Out of Your Washer
- Step 1: Power It Down and Turn Off the Water Supply. Start by powering down your machine. …
- Step 2: See If You Can Drain the Drain Hose. …
- Step 3: Check Out the Drain Pump. …
- Step 4: Drain the Interior Manually If Needed. …
- Step 5: Know When to Call a Professional.
How do you unblock a washing machine drain?
To unclog a clogged drain, first fill a bucket with boiling water and a pack of baking soda. Remove the drain pipe from your washing machine and slowly pour the water into the drain using a funnel. Wait a few minutes and test if it keeps draining if you pour water into it.
How do I know if my washing machine drain hose is clogged?
An easy way to check that the drain hose is clear is to blow air through it. If nothing is obstructing the drain tube, the problem is most likely at the washing machine pump. If the hose is worn or badly kinked, replacing the hose may improve the ability of the machine to pump water.
What causes a washing machine not to drain?
There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
Don’t forget to share the post !
