Dishwasher Troubleshooting: E22 Bosch Dishwasher Error Code
Table of Contents
READ ALSO
An E22 error code indicates that the dishwasher filter is blocked. The filter is the area where food particles get caught and it needs to be cleaned regularly. Remove the filter to make sure it is not clogged.
Likewise, How do you reset a Bosch dishwasher?
To reset the modern Bosch dishwasher, press and hold the start button for about 3 to 5 seconds. On some older Bosch models, the reset feature may be called “cancel” or “drain”.
Also, What does Error 24 mean on a Bosch dishwasher?
It means that the dishwasher is not draining properly due to the drain filter being blocked. Possible causes for the E24 error code: The drain hose could be blocked. … After fixing the problem, reset the dishwasher according to the owner’s manual.
Moreover, Why does my Bosch dishwasher say check water?
A Bosch dishwasher check water and rinse aid light flashing may indicate that the anti-flood switch has been activated. … This is often caused by a blocked drain or a faulty drain pump, and you may find water leaks under the machine.
Why is there standing water in my Bosch dishwasher?
If your dishwasher is clogged and not draining, check the filter and pump (located at the bottom of the dishwasher). … Check the pump and remove any debris and standing water you find with a sponge. Use caution as some debris may be sharp. Reinstall the pump cover and filter.
How do I fix e14 error on my Bosch dishwasher?
To get rid of pressure problems, tilt the appliance on 15-20 degrees to the left for a few minutes. If this method does not help, exclude a variant of a crash in the system, and try to reset the icons on the screen: disconnect the washer from the electricity for 10-15 minutes; connect it again after a while.
How do you run a diagnostic on a Bosch dishwasher?
For many Bosch dishwashers, this is done by pressing the “start” button and waiting for a response. If this doesn’t cause the cycle to resume or fix the problem, press and hold the “start” button for three to five seconds, then wait to see whether this works.
What does Error 25 mean on a Bosch dishwasher?
An E25 error code indicates the drain pump is blocked or the drain pump cover is loose or missing. What dishwasher troubleshooting do I need to do to fix the error code E25?
Why is the red light on my Bosch dishwasher blinking?
The flashing red light on a Bosch dishwasher indicates that the door is not latched correctly, which is required to initiate the wash cycle. … Replacing a faulty door latch sensor is usually required after about four years when this part starts to degrade and wear out.
How do you force a Bosch dishwasher to drain?
How do you force a Bosch dishwasher to drain? Push “Start” on the front of the dishwasher for three seconds to cancel the cycle. Wait at least one minute for “Clean” to light up on the dishwasher’s display.
How do I manually drain my Bosch dishwasher?
Hold the Start-Reset button for about 5 seconds or until the Active indicator turns off. Shut the door of the dishwasher to allow it to thoroughly drain before turning it off. When the dishwasher completes draining, it beeps to indicate that it is done.
What does Error 14 mean on a Bosch dishwasher?
Description: Bosch dishwasher e14 error code indicates that the flow meter is not registering that the water is entering the dishwasher. But the water is detected by the heatpump in the sump of the dishwasher. This is mostly caused by a faulty reed switch.
What is E14 error in Bosch dishwasher?
An E14 error code indicates a flow meter failure or an issue with water flowing into the dishwasher or the filling system.
How do you clear a Bosch error code?
How to reset an error code on a washing machine by Bosch, Neff, or Siemens. Press and hold down on the spin button and simultaneously turn the dial to the 7 o’clock position. Hold the spin button for around 5 seconds and then release.
What are the error codes for a Bosch dishwasher?
Bosch Dishwasher Error Codes and meanings
- Error E12: Limescale build up. …
- Error E14: Flow meter failure. …
- Error E15: Water in the base trough. …
- Error E16 & E17: Water filling the system. …
- Error E18: Water flow into the dishwasher. …
- Error E22: Filter is blocked. …
- Error E23: Issue with drain pump.
How do I fix Error 25 on my Bosch dishwasher?
The first thing to do when an e25 error occurs is to check the filter inside the dishwasher and the pump impeller. If the code appeared during the dishwashing, prepare for the fact that there may be too much water on the floor.
How do you drain a Bosch dishwasher?
For Bosch Dishwasher Ascenta models, open the door to reset it. Hold the Start-Reset button for about 5 seconds or until the Active indicator turns off. Shut the door of the dishwasher to allow it to thoroughly drain before turning it off. When the dishwasher completes draining, it beeps to indicate that it is done.
Why is my Bosch dishwasher not starting?
To prevent leaks, your Bosch dishwasher won’t start if the door isn’t securely closed and latched. … When starting the dishwasher, make sure the door is completely closed to engage the latch and switch. Signs of a broken dishwasher latch or switch include the dishwasher not starting even if the door is properly closed.
Why cant I change the settings on my Bosch dishwasher?
Why can’t I change the cycle on my Bosch dishwasher? As with other home appliances, you need to reset your Bosch dishwasher because of a problem, or to make a cycle change or to cancel a chosen cycle. The easiest way to interrupt a chosen cycle on most models is to hold the On-Off button for at least 10 seconds.
What does cleaning display light mean on Bosch dishwasher?
The action that it is instructing you to take is to empty the dishwasher, because the contents are clean, before loading the DW with any dirty dishes.
How do I force my dishwasher to drain?
How to Drain Your Dishwasher
- Step 1: Prepare Your Dishwasher. …
- Step 2: Make Sure Your Dishwasher is Turned Off. …
- Step 3: Remove the Stagnant Water With a Towel. …
- Step 4: Perform a Check On the Drain Hose. …
- Step 5: Remove Drain Hose and Clean. …
- Step 6: Check Dishwasher Drain.
How do I fix the error code E09 on my Bosch dishwasher?
If the E09 error code appears on the appliance display it means that your heating element is defective. If your salt LED is on at the same time, please check that your dishwasher salt sensor isn’t dirty and causing your appliance to assume there’s dishwasher salt when it hasn’t been topped up.
How do you fix an e19 error on a Bosch dishwasher?
It is also called a drain valve. And if you face this error, you should start checking the elements of the Bosch dishwasher and especially pay attention to the recirculation valve. To do this, you have to remove the detail and check the loop. The heat-exchange unit is considered to be a patented technology from Bosch.
What is E16 error on Bosch washing machine?
Washing machine troubleshooting: error code E16 or F16
These error codes indicate that the door is open. Please close the door and proceed as usual. If you’re still getting the error after closing the door, please verify it’s properly closed.
