Bonnie Frerking ,”the F70 and F71 error codes on this model of washer indicates a communication problem between the user interface control board and the central control unit (main control board). These error codes can sometimes be caused by a power surge or glitch through the electrical lines.
Table of Contents
READ ALSO
Likewise, What does F70 mean on a washer?
The F70 error on this model washer is a central control unit (CCU) heartbeat failure. This means there is communication loss from the central control unit and the user interface. The troubleshooting procedure for this error is to first check the wiring and connections between the main control and user interface.
Also, What does F71 mean on a Kenmore washer?
F71. means that there was not communication detected from the keypad to the central control unit. Attempt to return the washer to operation by following the. Hard Reset. procedure below.
Moreover, What does F70 mean on a Whirlpool Duet dryer?
The F70 error code on a Whirlpool dryer means the User Interface Board and the Main Control Board have stopped communicating with each other. Firstly, reset the dryer by shutting off the power supply and turning it back on a minute later.
What does OL mean on Whirlpool Cabrio washer?
The OL error code indicates that the washer is overloaded. If the washer is not overloaded, this would indicate either a drag on the drive system or the control board is failing. Be sure nothing is on the floor under the washer that could be causing a problem.
What does F7 mean on a Kenmore oven?
The F7 error code on your oven indicates the touch pad has failed. To repair it you will need to replace the touch pad which is listed as a control panel w/keypad in the parts diagram. If you do the repair yourself, disconnect the power to the oven.
What does F70 mean on a Kenmore dryer?
The F70 error code indicates a loss of communication between the console panel and machine (main) control board. Disconnect the dryer cord from the power supply and remove the top panel and check for loose connections on each control board.
What does F01 mean on a Whirlpool dryer?
The F01 error code means the primary control unit in the dryer has failed and will have to be replaced. The control that needs replacing is the electronic control board not the user interface and/or control panel.
Where is the error code on a Whirlpool Duet dryer?
Unplug the dryer for 5 minutes and then plug it in. If the code returns, replace the main electronic control board. A button is stuck on the keypad on one of the two user interface control assemblies in the console. If you can’t free the button, replace the user interface control assembly with the stuck button.
How do you troubleshoot a Whirlpool Duet dryer?
How to Troubleshoot a Whirlpool Duet Electric Dryer
- Inspect household fuses or breakers. …
- Close the dryer door firmly. …
- Press and hold the “Start” button for five seconds. …
- Check the display on the dryer for error codes.
What does F70 mean on a Whirlpool dryer?
Posted: 09/01/14. Doug, F70 means check harness connections at the machine control and at the console electronics. If your connections are fine to the machine control board and the console electronics, then you may need to change the machine control board.
Why does my washer say ol?
If OL (overloaded) appears in display, the load too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent. Close lid and press START/PAUSE.
Can you reset a Whirlpool Cabrio washing machine?
How To Reset Whirlpool Cabrio Washer: Turn the washer off. … Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
How do you fix the UL code on a Cabrio washer?
If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.
What does F7 on my oven mean?
F7= Shorted Clear/Off Key due to membrane switch, control or connector. Shorted key panel membrane switch, check the Electronic Range Control (ERC). GE – Range/Stove/Oven Fault Codes. F7= Function pad button stuck. Unstick button, bad clock, or replace Electronic Range Control (ERC).
What does it mean when your oven says F0?
GE profile oven gives error code F0 (or FO) The error code means a button on the touch pad is shorted or the control board is bad, they are fairly easy to replace but you will first need to determine if the touch pad or control is bad.
What does F70 mean on a Miele dishwasher?
After 4 years of using the Miele Optima Series Dishwahser, we started receiving an F70 error code. Called the Miele Tech support and they said we have been using too much soap over the years and the soap debris and bubbles were causing the float in the under pan to set off the F70 code.
What does error code F01 mean?
The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.
Why does dryer say F1?
The “F1” error means that the dryer’s thermistor failed. The dryer is reading the thermistor as “open” and the actual part has shorted out. The thermistor is used to read and control temperatures within the dryer. Without the part, the dryer will not operate.
How do I fix F1 error on my Whirlpool dryer?
When the Whirlpool Cabrio displays an F1 error, this means the the control board is having difficulty communicating with the motor. To fix your F1 error, you can first try to unplug your washing machine for 15 minutes and then plug it back in. If this doesn’t work, you will need to replace the control board.
What does AF on the dryer mean?
An AF (Restricted Air Flow) error code indicates that the lint screen or house vent is clogged; the vent may be crushed, kinked or have too many turns. The dryer will continue to run when the is error is present. Touch any key to clear the code from the display and return to the estimated time remaining.
How do I reset my Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
How do you troubleshoot a Whirlpool front load washer?
Troubleshooting Common Duet Washer Problems
- Unplug the washer for 30 seconds to attempt to reset the Duet washer control.
- Attempt a Duet Washer Quick Diagnostic Test.
- Check the power supply at the wall with some other device. If the wall plug has power…
- Check the Duet Line power filter.
- Check power at the control.
How do you run a diagnostic on a Whirlpool Duet washer?
Duet Washer Diagnostic Test Mode
Pick any three buttons on the Duet washer control except power, start, or cancel. Now do the key dance within eight seconds… Button 1, Button 2, Button 3, Button 1, Button 2, Button 3, Button 1, Button 2, Button 3 (You are pressing 9 buttons in 8 seconds so it needs to be pretty quick.)
