The PAU, or pause, error usually means that the washing machine cycle was interrupted and was not restarted properly. … If the washer was stopped midcycle and not restarted, the cycle must be canceled or completed before a new selection can be made.
similarly, How do you run a diagnostic test on a Frigidaire Affinity washer?
The diagnostic test is performed by using the program knob . To start the test: # On non-digital display models, turn the program knob to the start position, Drain/Spin.
…
- Wake the washer by pressing any button.
- Wait 5 seconds.
- Press and hold the Start/Pause and Cancel buttons simultaneously.
on the other hand, How do you clear error codes on Frigidaire Affinity washer?
To clear latest stored error code:
Turn the program knob clockwise 9 clicks from the Start Position. The control will signal the last error code. Press and hold the Options and Pause Cancel buttons for 3 seconds. The code will be cleared.
also, How do I troubleshoot my Frigidaire Affinity washer? How to Troubleshoot a Frigidaire Affinity Washer
- Stop the washing machine if rattling or clanking sounds occur. …
- Redistribute the load if you hear a thumping sound. …
- Level the washer if the machine vibrates. …
- Plug the power cord in and check household fuses or breakers. …
- Turn the water supply faucets on completely.
Why does my front loader keep pausing?
The door latch can cause a GE frontload washer to pause during a cycle. If the door physically opens, the washer will pause. However, if the door stays locked but the switch is bad then the control will think the door is open and the washer will pause.
How do you run a clean cycle on a Frigidaire Affinity washer?
Simultaneously press the “Spin Speed” and “Options” buttons until the cycle status display reads “Cln.” Then, add either one cup of liquid chlorine bleach or one pouch of Tide Washing Machine Cleaner to the detergent receptacle.
How do I find the error code on my Frigidaire Affinity washer?
the failure code will appear in the display as an E followed by two numbers, a number and a letter or two letters .
…
How to retrieve the error codes in a Frigidaire Affinity front…
- Wake the washer by pressing any button.
- Wait 5 seconds.
- Press and HOLD the Start/Pause and Cancel buttons simultaneously.
How do I reset my Affinity front load washer?
How to Reset the Settings on a Frigidaire Front Washer
- Verify that your Frigidaire front washer is plugged into a working electrical outlet and turned on; otherwise, you won’t be able to reset it.
- Press and hold the “Spin Speed” and “Soil Level” buttons together for a few seconds.
How do I clean my affinity washing machine?
Add two cups of white vinegar and let the cycle run. (If you have a front load washer, pour the vinegar into the detergent dispenser.) For an extra-clean washing machine, repeat the cycle with a half-cup of baking soda. Finally, spray the front or top with vinegar and wipe it down.
How do I fix e20 error on my washing machine?
Resolution:
- Ensure correct position of the drain hose. …
- Ensure correct drain height. …
- Clean the pump and filter. …
- Check for blocked drain. …
- Check the drainage hose for possible kink or twist. …
- Use less soap powder. …
- Switch off the power to the machine. …
- Contact an Authorized Service Centre.
Why is my Frigidaire Affinity washer not starting?
First ensure that power is getting to the electrical outlet. If the electrical outlet is receiving power, but the washer won’t start, the power cord might be defective. … To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.
How do you reset a Frigidaire Affinity front load washer?
Verify that your Frigidaire front washer is plugged into a working electrical outlet and turned on; otherwise, you won’t be able to reset it. Press and hold the “Spin Speed” and “Soil Level” buttons together for a few seconds. Continue holding the buttons until a signal sounds then release them.
Why is my washing machine stopping mid cycle?
Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. … The pump could also be to blame if your washer is failing to drain.
What is water inlet valve?
The water inlet valve on your washing machine is the part that connects the two water hoses to the machine, and it controls the flow of both hot and cold water. A problem with the valve can cause the washer not to fill properly or not fill at all.
How do I reset the lid lock on my GE washer?
Top Load Washer – Lid Lock Feature
- Make sure the washer is paused (press Start/Pause). During spin, this can take up to 3 minutes for the basket to stop spinning and allow you to open the lid.
- Unplug the washer for a minute to reset.
Does Frigidaire make washing machines?
Washers: Top-Loading Washing Machines by Frigidaire.
Why does my front load washer keep pausing?
The door latch can cause a GE frontload washer to pause during a cycle. If the door physically opens, the washer will pause. However, if the door stays locked but the switch is bad then the control will think the door is open and the washer will pause. If the door will not latch then the washer will not start.
How do you unlock an affinity washing machine?
To complete the Frigidaire front load washer door latch bypass can be quickly done by pressing the control lock button for five seconds. This should disable the lock. Push the start/pause button to stop the current wash cycle.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
Can I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
Why is my washing machine saying error?
Common appliance codes could be related to a problem with the door, a water heating sensor, a software or circuit board fault, a motor or pump fault plus much more. Simple things that could have an error code could be the door being left ajar on the machine or the detergent drawer not in situ properly.
Why is my washing machine saying E21?
E21 – Drain flow error. This error will be displayed when the unit senses that the drain process is taking too long. This error may be caused by a blockage occurring in the coin trap or in the drain line. … Clean out the coin trap regularly to ensure normal operation of washing machine.
What would cause a washing machine not to start?
If your washer will not start, be sure the switch is being pressed. If the lid switch is being pressed but no power is being supplied to the washers motor, then the switch is most likely bad. To test the switch, turn off power to washer and remove the wires from the lid switch.
How do I start affinity washing machine?
How to Start a Frigidaire Affinity Washing Machine
- Prepare your laundry by sorting same colored clothes together. …
- Open up the Frigidaire Affinity washing machine and place the clothes inside. …
- Open the dispenser on the upper left-hand side of the machine and add the laundry products.
Why does my washer have no power?
No power issues are typically caused by a tripped circuit breaker, a faulty electrical outlet, a power outage in the home, or in rare cases a unit that requires a repair.
Don’t forget to share the post !
