OE error code indicates that the washer is unable to drain the water it used during the wash cycle. OE can be triggered by a kinked drain hose or a clogged drain pump filter.
similarly, How do I rebalance my washing machine?
If your washer is located on a pedestal, the problem can be amplified. Top-loading washers automatically adjust to level. If something has shifted, you can relevel a top-loading washer by tipping the washer forward, then placing it back on the floor. Front-loading washers level by turning a leg to raise or lower it.
on the other hand, How do I fix OE error on my LG top load washer?
Force drain the unit by starting a cycle and pausing it.
…
If you don’t have SPIN ONLY
- Power the unit ON.
- Select a cycle.
- Press START/PAUSE button to START the cycle.
- Allow a few minutes to pass so the cycle begins.
- Press the START/PAUSE button to PAUSE the cycle.
- Run an empty wash cycle to see if issue occurs again.
also, How do I know if my washing machine drain pump is bad? You can check by looking for a few signs that a pump is dying or already dead.
- Start the washer and wait for the washer tub to fill with water. If you do not hear water or hear a motor whirring, the washer motor may be dead.
- Open the washer lid in mid-cycle. …
- Wait for the washer to finish its cycle.
How do I manually drain my LG washer?
If you want to perform a drain-only cycle, turn on your LG washer and press the spin button and then press start. After a few minutes, the cycle will end and your washer should have drained out the water. Another way you can drain the water is by turning off your washing machine and unplugging it from the outlet.
Why does my washer keep going off balance?
Laundry caught below the tub or between the agitator and the inner tub can cause the washer to operate off balance with every load. The problem can be anything: a penny that worked its way out of a pocket, a button that fell off a shirt or a wayward sock or other article of clothing.
Why is my washer always unbalanced?
One or more of the suspension springs might be broken. The suspension springs help to absorb the movement of the washer tub. If a suspension spring breaks, the tub might become unbalanced, causing it to shake and vibrate during operation. Inspect the suspension springs to determine if any of the springs are broken.
How do you rebalance a front-load washer?
Loading and Distributing the Laundry
- Open the front-load washer door. Manually redistribute the load inside the drum. …
- Add more items to the wash. A single, bulky item, such as a comforter or blanket can cause the unbalanced load. …
- Avoid overloading your front-load washer.
Why isnt my LG washer draining?
Unbalanced Load. One of the most common reasons your LG washer won’t drain often results from an unbalanced load. Washing a large or heavy item can cause it to settle on one side of the washer drum. When this happens your LG washer won’t drain or spin properly and water will be left behind.
How do I reset my LG top loader washing machine?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do I troubleshoot my LG washer?
How to troubleshoot:
- Open the stop valve to its full capacity. It may be closed or opened insufficiently.
- Check the intake hose. …
- The filter screen may be clogged with debris as well. …
- The intake valve is malfunctioning. …
- If the pressure switch is broken, you can repair your LG washing machine yourself.
How do I test my LG washing machine drain pump?
Test the drain pump.
- Press POWER to turn the washer ON.
- Press the SPIN SPEED key until HIGH is selected.
- Press the START/PAUSE button to start the SPIN ONLY cycle.
- Listen to hear a humming sound which indicates that the drain pump motor has started working.
Where is my washing machine drain pump?
The drain pump may be located behind removable panels in either the front or back of the washing machine, even underneath the appliance, requiring you to tip the machine forward to access it (consult your owner’s manual for instructions). You’ll see a drain hose and inlet hose connected to it with spring clamps.
What do you do when your washing machine won’t drain water?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
Why is my washing still wet after spinning?
The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. … Often with this issue, whatever is causing it to not drain during the spin cycle means the water isn’t draining off fast enough and is essentially flowing back into the washer drum, re-soaking your clothing.
How do you force a washer to drain?
How to Manually Drain a Top-Loading Washing Machine
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose at the back of the washing machine. …
- Step 3: Drain the water. …
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose. …
- Step 3: Drain the water. …
- Step 4: Scrub the filter.
How do I fix UE error on LG washer?
- Run rinse and spin cycle without load. Empty the drum completely. Power the unit on. …
- Request Repair. If the uE or UE error displays again, the unit is not working properly; it requires a repair service. …
- Leveling, load distribution, and selected washing cycle. The unit does NOT require a repair service.
How do I stabilize my washing machine drum?
Tilt your top-loading washing machine over at an angle to allow any standing water to flow out of the drainage opening. Place a towel over your water supply hose ending and hold it in place with a rubber band. Lay the covered end of the hose inside the washing machine drum.
Do front load washers need to be balanced?
It is important to balance your washing machine during installation and, if necessary, rebalance again later. An unbalanced washer does not clean or drain clothes properly. Balancing or rebalancing your washer also helps prevent damage to the machine and extends its life.
Why won’t my washer drain the water?
There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
How do I clear the IE code on my LG washer?
Turn off the home’s hot and cold water supply taps/valve. Remove the water inlet hoses from the washer. Ensure to have a bucket to drain the remaining water from the hoses. Check the inlet filters on the inlet valves of the washer, inspect for any mineral deposits or other debris that may be clogging them.
Can you factory reset a washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do I change the default settings on my LG washer?
Press the Power button. – The lights around the cycle selector knob will illuminate and a chime will sound. Turn the cycle selector knob to the desired cycle. – The optimum default cycle settings are automatically set according to the wash cycle.
Don’t forget to share the post !