OE error code indicates that the washer is unable to drain the water it used during the wash cycle. OE can be triggered by a kinked drain hose or a clogged drain pump filter.
similarly, How do I reset my LG washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
on the other hand, How do I fix OE error on my LG top load washer?
Force drain the unit by starting a cycle and pausing it.
…
If you don’t have SPIN ONLY
- Power the unit ON.
- Select a cycle.
- Press START/PAUSE button to START the cycle.
- Allow a few minutes to pass so the cycle begins.
- Press the START/PAUSE button to PAUSE the cycle.
- Run an empty wash cycle to see if issue occurs again.
also, How do I know if my washing machine drain pump is bad? You can check by looking for a few signs that a pump is dying or already dead.
- Start the washer and wait for the washer tub to fill with water. If you do not hear water or hear a motor whirring, the washer motor may be dead.
- Open the washer lid in mid-cycle. …
- Wait for the washer to finish its cycle.
How do I manually drain my LG washer?
If you want to perform a drain-only cycle, turn on your LG washer and press the spin button and then press start. After a few minutes, the cycle will end and your washer should have drained out the water. Another way you can drain the water is by turning off your washing machine and unplugging it from the outlet.
How do I fix UE error on LG washer?
- Run rinse and spin cycle without load. Empty the drum completely. Power the unit on. …
- Request Repair. If the uE or UE error displays again, the unit is not working properly; it requires a repair service. …
- Leveling, load distribution, and selected washing cycle. The unit does NOT require a repair service.
How do I clear the IE code on my LG washer?
Turn off the home’s hot and cold water supply taps/valve. Remove the water inlet hoses from the washer. Ensure to have a bucket to drain the remaining water from the hoses. Check the inlet filters on the inlet valves of the washer, inspect for any mineral deposits or other debris that may be clogging them.
Can you factory reset a washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
Why isnt my LG washer draining?
Unbalanced Load. One of the most common reasons your LG washer won’t drain often results from an unbalanced load. Washing a large or heavy item can cause it to settle on one side of the washer drum. When this happens your LG washer won’t drain or spin properly and water will be left behind.
How do I troubleshoot my LG washer?
How to troubleshoot:
- Open the stop valve to its full capacity. It may be closed or opened insufficiently.
- Check the intake hose. …
- The filter screen may be clogged with debris as well. …
- The intake valve is malfunctioning. …
- If the pressure switch is broken, you can repair your LG washing machine yourself.
How do I test my LG washing machine drain pump?
Test the drain pump.
- Press POWER to turn the washer ON.
- Press the SPIN SPEED key until HIGH is selected.
- Press the START/PAUSE button to start the SPIN ONLY cycle.
- Listen to hear a humming sound which indicates that the drain pump motor has started working.
Where is my washing machine drain pump?
The drain pump may be located behind removable panels in either the front or back of the washing machine, even underneath the appliance, requiring you to tip the machine forward to access it (consult your owner’s manual for instructions). You’ll see a drain hose and inlet hose connected to it with spring clamps.
What do you do when your washing machine won’t drain water?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
Why is my washing still wet after spinning?
The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. … Often with this issue, whatever is causing it to not drain during the spin cycle means the water isn’t draining off fast enough and is essentially flowing back into the washer drum, re-soaking your clothing.
How do you force a washer to drain?
How to Manually Drain a Top-Loading Washing Machine
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose at the back of the washing machine. …
- Step 3: Drain the water. …
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose. …
- Step 3: Drain the water. …
- Step 4: Scrub the filter.
How do I drain the water from my washing machine?
5 Easy Steps to Get Water Out of Your Washer
- Step 1: Power It Down and Turn Off the Water Supply. Start by powering down your machine. …
- Step 2: See If You Can Drain the Drain Hose. …
- Step 3: Check Out the Drain Pump. …
- Step 4: Drain the Interior Manually If Needed. …
- Step 5: Know When to Call a Professional.
What does IE mean on UE washer?
The IE error code on the LG washers display is indicating water did not fill the tub or it did not fill properly in the allotted time. This can be from a faulty water inlet valve, drain hose issue, bent water hoses, the water valves to the washer are not “open”, or there may be a communication or wiring harness issue.
How do I force drain my LG washer?
If you want to perform a drain-only cycle, turn on your LG washer and press the spin button and then press start. After a few minutes, the cycle will end and your washer should have drained out the water.
How do I fix E1 error on my washing machine?
If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.
Does unplugging a washer reset it?
On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
What are common problems with washing machines?
7 Common problems with washing machine
- Washing machine not starting. …
- Washing machine is noisy. …
- Excessive vibrations during operation. …
- Washing machine making noise when draining or not draining at all. …
- Washing machine over-filling or under-filling. …
- Washing machine not spinning. …
- Water leaking from soap drawer.
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.
Why won’t my washer drain the water?
There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
Don’t forget to share the post !