The Samsung microwave error code E-11 indicates a humidity sensor issue. To locate the humidity/gas sensor or the wiring harness, check on the top left side of the microwave. It is located under the outer panel.
Table of Contents
READ ALSO
Likewise, What does it mean when your microwave says sensor error?
The error message is caused by opening the microwave door too early when you are using the sensor cooking function. Removing the error message from the microwave display takes only a moment.
Also, What does E 83 mean on a Samsung microwave?
E83 means that your control board has either failed or one of the door switches inside the microwave has failed. There are 3 door switches that you’ll need to test with a multimeter to see if one has failed.
Moreover, What is a humidity sensor in a microwave?
The humidity sensor detects humidity inside the microwave and communicates the temperature to the electronic control board.
What do you do when your microwave says error?
Indication of an issue with the electronic control in the microwave. Sometimes shutting off the circuit breaker or fuse that supplies power to the microwave oven for 30 seconds will clear the fault, error or function code.
What does E 10 mean in microwave?
First, error E10 means that your display control board itself has an internal short detected. You can try to unplug the microwave for 5 minutes to see if the electronics will reset but if that doesn’t work, the entire display board would need to be replaced.
How do I troubleshoot my Samsung microwave?
Samsung microwave is not heating or has stopped working
- Verify that the microwave is not in Demo mode. …
- Check the Kitchen Timer feature. …
- Inspect the door. …
- Verify there is enough clearance on all sides. …
- Request service.
What does F1 mean on a microwave?
Microwave – Error, Fault or Function Codes
| Fault Code | Definition |
|---|---|
| F1 | Open Thermal Sensor, due to excessive heat in microwave cavity |
| F2 | Shorted thermal sensor |
| F3 | Shorted touch pad panel |
| F4 | Open humidity sensor |
How do I reset my microwave?
Here’s how to reset a microwave via hard reset.
- Locate the plug of the microwave and pull that plug out of the socket.
- Wait for two to three minutes before plugging in the microwave.
- Turn on the microwave and set the time of the day by pressing the Clock button. Press the dial to enter the time, minutes, and the am/pm.
Where is the humidity sensor on a microwave?
The humidity sensor is installed in the machine room at a position adjacent to the sub-outlet to sense the humidity of the air inside the cooking cavity by sensing the humidity of a part of the air discharged from the cooking cavity through the sub-outlet.
What does sensor Reheat mean on a microwave?
Answer: Microwave sensor cooking measures vapor (moisture and humidity) emitted from food as it heats. To use the sensor cook option, press the desired cooking mode. Sensor Reheat can be used to reheat foods. Follow the menu guide on the microwave.
Why does my microwave say f4?
The F-4 indicates a failure in the humidity sensor in the microwave. This is normally caused by a failed sensor. In rare instances, it can be caused by a failed control board. Since this is an internal microwave component failure, I recommend calling a service technician to diagnose and repair the microwave.
Is there a fuse in a Samsung microwave?
The thermal fuse cuts off power to the microwave if the microwave overheats. To determine if the thermal fuse has blown, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it. The thermal fuse cannot be reset—if the fuse is blown, it must be replaced.
Why is my Samsung microwave not starting?
If your microwave is not turning on, or if it is turning off by itself, it could have overheated. When a microwave has been in use for a long time and overheats, just give it 30 minutes to cool off and then try to use it again. Otherwise, you’ll need to check the light, the outlet, and the power cord.
Is there a recall on Samsung microwaves?
announced a voluntary recall of approximately 43,000 Samsung over-the-range microwave ovens, citing a potential shock hazard. … The recall affects all Samsung 1000-watt over-the-range microwave ovens with the following model and serial numbers: SMH9151x from serial number xxxxxxxS1xxxxxx to xxxxxxxS5xxxxxx.
How do I fix F1 error?
To fix your Whirlpool F1 error code, you should first try to unplug your washing machine or disconnect power for 1 minute and then plug it back in/turn the power back on. Re-select the cycle and press Start. In some cases, disconnecting and reconnecting power to the unit clears the F1 error code.
How do I fix F1 error on my oven?
When an F1 error occurs, the display flashes the code and beeps at the same time. To stop the flashing and beeping, press the “Cancel” button. Try the bake or broil feature once more, and if the error code repeats, unplug the appliance and wait five minutes before plugging it back in.
Is there a reset button on microwaves?
Does a Microwave Have a Reset Button? Most microwave ovens do not include a reset button. … A hard reset happens when you physically unplug the microwaves’ cord from the wall outlet.
What is a hard reset on a microwave?
A hard reset is necessary. Take the plug out of the wall power supply. The microwave’s memory can be reset by plugging the microwave back into the wall power supply. If you perform a hard reset, you’ll need to change the time of day.
What causes a microwave to suddenly stop working?
The most common cause for a microwave oven not working at all is a blown main fuse. The microwave main fuse will cut the flow of electricity if too much current passes through it. … There can also be thermal fuses, cavity fuses, and thermoprotectors which will interrupt the electrical flow if the microwave overheats.
Do microwaves have humidity sensors?
Microwave sensor cooking uses temperature and humidity sensors inside the microwave to determine when the food is ready. When a microwave heats food, it excites the water in the food, causing it to give off steam as it heats.
What is a sensor cook microwave?
Answer: Microwave Sensor cooking measures vapor (moisture and humidity) emitted from food as it heats. To use the sensor cook option, press the desired cooking mode. Sensor Reheat can be used to reheat foods.
What does F5 mean on microwave?
Microwave – Error, Fault or Function Codes
| Fault Code | Definition |
|---|---|
| F4 | Open humidity sensor |
| F5 | Shorted humidity sensor |
| F6 | Shorted temperature probe |
| F10 | Shorted touch screen |
