Why does my washer say F9 E1?

If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. … If not, the washer could siphon (fills and drains at the same time).

Likewise, How do I reset my Whirlpool front load washer?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.

Also, How do you fix E1 F9 error on a Maytag washer?

F9 E1 Code in the display: Is the drain hose properly installed?
…
Is the drain hose properly installed?

1. Make sure the drain hose is not kinked or clogged.
2. Use the U-shaped drain hose form on the drain hose.
3. The standpipe (drainpipe) height requirements are 96″ (244 cm) maximum and 39″ (99 cm) minimum.

Moreover, What does E1 mean on my washer?

When the Washing Machine is displaying E1 in the panel, it is indicating an error in the water supply. The appliance is not detecting that the unit is filling with water. To resolve, checking the following: • Check whether the water supply is turned on and that there is adequate water pressure.

Why is my Whirlpool washer stuck on sensing?

A blinking sensing light indicates an underlying issue with the drain, spin, or any other function. There are several such problems that Whirlpool washers commonly run into. … The washer will function only when the lid/door is completely closed. The water pump belt in the washer has worn out or is damaged.

Why does my Whirlpool washer not start?

One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.

How do I clear the error code on my Maytag washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do I reset my Maytag washer?

How to Reset a Maytag Washer

1. Press the “Power/Cancel” button.
2. Push the appropriate button to choose a new cycle.
3. Press “Start/Pause.” You have now reset your Maytag washer.

What does E01 and F09 mean on a Maytag washer?

Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.

How do I fix E1 error on top loader washing machine?

If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.

How do I fix E1 error?

The Generic Approach

1. Turn off the air conditioner and unplug it.
2. Hold down the power button, and keep it depressed while you or someone else plugs it back in. Keep the button depressed while the fan and condenser cycle run briefly and cycle off again. …
3. Unplug the air conditioner again and plug it back in.

What does E1 F8 mean on a Whirlpool washer?

If F8 E1 or LF (too long to fill) appears in display, it means the washer is taking too long to fill. It’s possible the drain hose extends more than 4.5″ (114 mm) into standpipe. … If it does not detect both water supply hoses are turned on, the control detects a problem with the water pressure sensor.

How long should Whirlpool washer be in sensing mode?

These sensing spins may take 2 to 3 minutes before water is added to the load. The washer will then move the load briefly, pause to allow water to soak into the load, and resume adding water.

Why is my washer taking so long sensing?

A washer that continuously takes too long to wash may have a malfunctioning load sense system, or greater problems with its control panel. There may also be issues with your water inlet valve, which pulls water into the appliance for each cycle.

How do you fix a Whirlpool washer that won’t start?

Troubleshooting When Your Whirlpool Front Load Washer Won’t Start

1. Washer is unplugged: Make sure the power cord is plugged in to a functioning outlet.
2. Tripped circuit breaker: Check for tripped breakers in your home’s circuit breaker box, resetting any as needed.

Does my Whirlpool washer have a reset button?

Is there a reset button on a Whirlpool washer? Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds.

How do I force my Whirlpool washer to open?

Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.

Why does my Maytag washer not start?

If your Maytag washing machine isn’t starting, verify that the power cord is connected to a live outlet. Test the outlet with another three-prong appliance. … Select a wash setting and pull out the knob to start the cycle. If it still won’t start, reset the circuit breaker or change out the fuses if they are blown.

Why is my Maytag washer not working?

When your washer isn’t working right, the solution may be as simple as switching up detergents, tightening a hose or leveling the appliance. … If you have a front load washer, a dirty drain pump filter can be a common cause of the issues listed below, like problems draining, spinning and odor.

Why does my Maytag washer not fill with water?

If your Maytag Washer keeps filling or won’t fill up with water, you should check your water for improper installation or kinks in your water supply lines, inlet valves, and drain hose. These issues can also signify a faulty part in your household appliance, which may need to be serviced or replaced.

Why is my Maytag washer stuck on sensing?

If your Maytag washer’s sensing light is stuck and will not move to the appropriate cycles, this is usually caused by a stuck or keypad. The keypad can occasionally become jammed or, if you have recently replaced a part on the washer, you may have forgotten to recycle the codes, which can lead to a stuck sensor light.

How do you bypass the clean cycle on a Maytag washer?

Hello Sandy, Press and hold the “Spin” and “Soil” button simultaneously for 10 seconds. A countdown will be displayed on the console. Once the countdown has completed the unit will have successfully reset.

Why is my washer stuck on sensing?

When Kenmore HE Washer is stuck on Sensing Cycle and not proceed to the Wash cycle, most likely one of these 3 parts malfunction: Failed Water Inlet Valve or Inlet Valve Tap is in OFF position. Shift Actuator not able to change position, before Wash cycle. Control Board malfunctioned.