If your Maytag washing machine isn’t starting, verify that the power cord is connected to a live outlet. Test the outlet with another three-prong appliance. … Select a wash setting and pull out the knob to start the cycle. If it still won’t start, reset the circuit breaker or change out the fuses if they are blown.
Likewise, How do you reset the error code on a Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Also, How do you fix a washer that won’t start?
How to Fix a Washing Machine That Won’t Start
- Activate the power button.
- Test the outlet.
- Reset outlet if necessary.
- Make sure the power cord is plugged in.
- Check if fuses are blown or the circuit breaker is thrown.
- See if Delay Start has been pushed.
- See if Control Lock has been activated.
Moreover, Why is my washing machine not turning on?
Power Source
Make sure the machine is tightly plugged in. Next, check for a tripped circuit breaker. Reset the breaker and try to start the washer. If neither is at fault, you may have a damaged power cord.
Where is the fuse in a Maytag washer?
Maytag washers have a fuse in the lid-switch assembly. Maytag top-loading washers have a fuse in the lid-switch assembly. When you close the lid after adding the laundry and soap, the lid’s plastic switch contacts with the assembly underneath.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do you fix a Maytag washer that won’t drain?
If the washer won’t drain or is not draining properly, and the washer has a coin trap, remove the coin trap and clean it thoroughly. First, check the drain hose to determine if it is kinked, twisted, or bent. If the drain hose is bent, straighten it out. In addition, remove the drain hose and check it for obstructions.
Why is my Maytag washer stuck on wash cycle?
Maytag washer keeps spinning for various reasons like a faulty driver belt, defective motor control board, and a worn-out clutch band kit. Your washer might be stuck in the spin or rinse cycle when you use excess power detergent, timer issues, drain control issues, and electrical problems.
Why does my Whirlpool washer not turn on?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
Is there a reset button on a Whirlpool washing machine?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How dO I know if my thermal fuse is blown?
How to tell if a thermal fuse has blown? To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown. Learn about testing for a blown fuse.
How do I change the fuse in my Maytag washer?
Maytag washers have a fuse in the lid-switch assembly.
- Turn the circuit breaker to the washer off.
- Open the lid of the washer.
- Insert a screwdriver in one screw in the lid-switch assembly.
- Pull the top of the lid-switch assembly straight up and off.
- Set a multimeter to x1 ohms and turn it on.
Is there a fuse on a washing machine?
Washing machines have fuses that protect them from power surges. Washing machines require lots of power to run. … The other fuse sits in the lid switch on some machines; if the washer overheats or there is a power surge, the washer will not run again until the fuse in the switch is replaced.
Will unplugging a washing machine reset it?
On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
How do I reset the control panel on my Whirlpool washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I reset my top load washer?
Motor Reset Procedure:
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
- The motor has now been reset and is ready for you to start a cycle.
Why is my Maytag washer not draining or spinning?
Drain Hose is Kinked or Clogged
A hose that’s kinked or clogged by lint or debris causes a washing machine not to drain because water can’t bypass the blockage. … To remove any kinks, disconnect the hose clamp at the washer and gently straighten the hose. The hose must also be unclamped to assess any blockages inside.
How do you unclog a Maytag washer?
- Prepare the Machine. Pull Away from the Wall. With your supplies ready, it’s time to prep the washing machine. …
- Clear the Water. Bail Out the Basket. If the washer is full of water that isn’t draining away, you’ll need to bail it out. …
- Remove the Front Panel. Prop Up the Washer Front. …
- Start the Clog Hunt. Check the Pump Housing.
How do I know if my washing machine drain hose is clogged?
An easy way to check that the drain hose is clear is to blow air through it. If nothing is obstructing the drain tube, the problem is most likely at the washing machine pump. If the hose is worn or badly kinked, replacing the hose may improve the ability of the machine to pump water.
Why is my washer not going through cycles?
One common issue that can cause a washing machine’s cycle to stop is the heater to stop working properly. To test this set your washer on a cycle and monitor it every so often, if the cycle stops within the first 30 minutes then the water likely isn’t getting sufficiently heated.
Why is my washer stuck on one cycle?
If your top load washing machine (or some older front load washers) is stuck on one continuous cycle and will not advance and forward to the next wash cycle, then most likely the washer timer is faulty and needs replacement. The timer on your washing machine controls all aspects of the wash, spin, and rinse cycles.
Why wont my washer go past the wash cycle?
A top-load washer won’t advance to the drain and spin cycle if a broken lid switch is making the timer think the washer lid is open. A washing machine that won’t finish the cycle could also have a broken timer or failed water-level pressure switch.