A remote control that will not respond or control your TV usually means low batteries. Make sure you are pointing the remote at the TV. There also may be something interfering with the signal such as other electronics, certain types of lighting, or something blocking the TV remote sensor.
Table of Contents
READ ALSO
Likewise, Why won’t my Samsung remote change the channel?
If you cannot change channels on your Samsung smart TV, first double-check to ensure your Samsung remote is programmed with your cable box. If afterward, you have confirmed your remote and cable box are connected, you will need to reset your remote.
Also, Why won’t my remote let me change channels?
Check the batteries in your remote control. If you do not see at least 1 button lighting up on the remote upon pressing the button, then the batteries may be depleted. Change the batteries in your remote control and retest. Power down your set-top box using the “CBL” button on the remote and then power it back up.
Moreover, How do you sync a Samsung remote?
On most Samsung TVs, the remote control sensor is located on the lower right hand side of the TV. If not, it is directly in the bottom center. Next, press and hold the Return and Play/Pause buttons simultaneously for at least 3 seconds. Your TV will begin syncing with the Smart Remote.
Why does TV remote not change channels?
Remote will not change channels or turn on the TV. Batteries are low, dead, or inserted incorrectly. Verify the batteries are inserted in the correct direction. … If the box turns ON or OFF, then install new batteries in the remote and try again.
How do I get my directv remote to change channels?
Make sure your remote is paired with your receiver.
- Point the remote at your Genie, Genie Mini, or Wireless Genie Mini.
- Press and hold MUTE and ENTER at the same time on your remote.
- The screen displays Applying IR/RF Setup. The remote is synced.
How do I reset my cable remote?
To perform a factory reset:
- Press the Setup button until the LED at the top of the remote changes from red to green.
- Press 9-8-1.
- The LED will blink green twice to indicate that the remote was reset.
What to do when remote is not working?
Section B: Checking items of the remote control (common)
- Make sure none of the remote buttons are jammed.
- Reset the remote. …
- Clean the remote control terminals. …
- Replace with fresh batteries. …
- Perform a power reset on the TV. …
- For Android TV/Google TV: symptoms may improve by updating the software of the remote control.
How do I program my Samsung AH59 remote?
How to Use a Samsung Remote Control Model AH59-01778F
- Push the “TV” button on the remote.
- Push and hold “Power” while entering one of the two-digit codes listed for your TV’s manufacturer in the User’s Manual of your Samsung home-theater system.
- Release the “Power” button, then push the “Power” button again.
How do you pair a remote to a TV?
The next steps will depend on your TV menu options:
- Select Remotes & Accessories — Remote control — Connect via Bluetooth or Activate button.
- Select Remote control — Connect via Bluetooth.
- Select Voice Remote Control — Activate button.
Why does my Samsung Remote say not available?
If your Samsung remote keeps saying that it is not available, turn your television set off and allow it to completely drain of power. Once this is completed, turn the TV back on and simultaneously hold down the ‘Return’ and ‘Play/Pause’ button on the remote control as the TV starts back up.
How do I fix an unresponsive remote?
Clean the remote control terminals. The remote control battery terminals may be dirty. Remove the batteries and clean the remote control terminals with a small solution of alcohol, using a cotton bud or soft cloth, then place the batteries back into the remote control. Replace with fresh batteries.
How do I sync my genie remote to my TV?
Point the remote at your Genie HD DVR, Genie Mini, or Wireless Genie Mini. Press and hold the MUTE and ENTER buttons. Stop when the green light at the top of the remote blinks twice. When the TV screen displays Applying IR/RF setup, you are in RF mode and ready to program the remote.
Can I use my DirecTV remote as a universal remote?
One of the problems that people who have DirecTV run into is that after their DirecTV dish and box are installed, they receive a new DirecTV remote control that is not preset to control their television. However, DirecTV remotes are universal remote controls, which means that you can program them to work with any TV.
How do I pair my x15 remote?
Press and hold the xfinity and Info buttons for five seconds. Wait for the Voice Remote light to change from red to green. Follow the instructions by entering the three-digit, on-screen pairing code. Once the on-screen pairing code is correctly entered, your Voice Remote is paired with the TV Box.
How do I link my remote to my Samsung TV?
On most Samsung TVs, the remote control sensor is located on the lower right hand side of the TV. If not, it is directly in the bottom center. Next, press and hold the Return and Play/Pause buttons simultaneously for at least 3 seconds. Your TV will begin syncing with the Smart Remote.
How do I pair my xr11 remote?
Be sure to point the remote at your equipment during setup.
- Press and hold SETUP until the LED turns GREEN.
- Press the Xfinity button.
- Follow the TV on-screen instructions to enter the 3-digit code that appears.
- The remote is now paired and voice commands should work when you hold down the VOICE CONTROL key.
Why is my remote not working even with new batteries?
The remote control battery terminals may be dirty. Remove the batteries and clean the remote control terminals with a small solution of alcohol, using a cotton bud or soft cloth, then place the batteries back into the remote control. Replace with fresh batteries.
What is the mode button on Samsung remote?
Use the “Mode” button on the remote control to highlight the device you want to program. For example, if you want to program your DVD player, press the “Mode” button until the indicator light comes on under “DVD.” If your remote control has separate buttons for each device, press the button with the correct label.
How do you reprogram a universal remote control?
Here is an example of likely steps:
- Turn on your TV or another device you wish to control.
- Press and release the DEVICE button on your remote that is associated with the product you want to control (TV, etc.). …
- Press the Device Button again, as well as the POWER button at the same time. …
- Release both buttons.
How do I sync my Samsung DVD remote to my TV?
Samsung Remote Program guide for DVD Player
- 1 – Turn your DVD player off.
- 2 – Press the Mode button on your remote to switch the remote to DVD mode. …
- 3 – Press the Set button on the remote control.
- 4 – Enter the three digit DVD player code listed in your TV’s user manual. …
- 5 – Press the Power button on the remote control.
Why does my Samsung remote keep blinking?
1) If the status light on your Samsung Remote flashes red repeatedly this means either your TV has become unpaired from the TV or your remote batteries are dead. (See instructions and video below).
How do I get my Samsung Smart TV remote to work?
Using the On-Screen Remote
Press the MENU/123 button on the Samsung Smart Control to display the On-Screen Remote on the TV’s screen. Use the On-Screen Remote to enter numbers and control content playback. Select buttons on the top of the screen to use the features and functions of the TV, just like a real remote.
What is a Samsung Smart remote?
Dubbed the Samsung Smart Control, the remote is based on the company’s Tizen operating system, a mobile platform it’s developed to run on everything from televisions to smartphones. …
