for both 15A and 20A circuits the rule of thumb is a maximum of 10 receptacles per circuit. 15 amp breaker circuit 14/2 wire. … In general it’s “safe” to use a larger wire-size than required and the smallest fuse or breaker ampacity that the equipment will permit.
14-2 can only be used for 15A circuits. 12-2 can be used for 15A circuits or 20A circuits. If you are in the US, you can use 12-2, a 20A breaker, and 15A receptacles (as long as you have more than 1 receptacle on the circuit). Its fine for 15 or 20 Amps.
Thereof, Can I mix 12 and 14 gauge wire on a 15 amp circuit?
Yes you can mix 12 and 14 gauge wire with a 15 amp breaker on the circuit. But it is not recommended because the next homeowner or electrician may be confused and put a 20 amp breaker on it again.
Also to know is, Where can I use 12 2 wire? Romex is used for most lighting and outlet circuits in your home. Romex will be labeled with “12-2” or “12-3”. The first number indicates the gauge of the wire.
Subsequently, question is, Can I mix 12 and 14 gauge wire? The amp capacity for 12-gauge wires is 20 amps, and while you can technically use 14-gauge wires on 20-amp circuits, it is not recommended.
Also, Is it OK to mix wire gauges?
Mixing Wire Gauges To prevent overloading, use the same gauge wire throughout a circuit. And take care to use the right size wire for the amount of amps in the circuit. Don’t go on the look of a wire. Know the amp capacity for each gauge of wire.
Can you use 14 gauge wire on a 20 amp circuit?
You can not use 14 AWG anywhere on a circuit that has a 20A breaker. If you are putting 15 amp receptacles on a 20 amp circuit with 12 gauge wire, then you MUST use the screw terminals, not the back stab terminals. … Just use the side terminals.
Can you use 12 2 wire for a dryer?
3 Answers. 10/3 is FINE for the dryer. 12/2 for the washer. Typically a 220v/30 amp Dryer circuit would utilize 10/3 with ground.
Can you use 10 2 wire for a dryer?
If your dryer does not require the neutral, and is a pure 220V appliance, than you can use the 10-2 and be code compliant.
Can I use 14 gauge wire for outlets?
Yes you may use No. 14 AWG Cu wire for outlets but the Circuit Breaker to protect the circuit should be only 15A. Do not use 20A Circuit Breaker for this circuit. … The circuit should not have more than 10 receptacles.
How many outlets can you put on a 14 2 wire?
12 outlets
What happens if you use too small gauge wire?
If too small of a size is used, the wire could melt because of the large amount of current flowing through it compared to how much the cables can handle. The smaller the wire diameter, the higher the resistance there will be to the flow of energy.
What kind of wire do I need for a dryer?
The NEC requires that dryers have a dedicated circuit with a minimum of 30 amps. This calls for a 30-amp, double-pole breaker wired with 10 AWG wire.
How many outlets can you put on a 15 amp circuit?
10 outlets
What is 10 2 Romex used for?
Wire Gauge or Type Rated Amperage Common Uses
—————— ————– ——————————————
14-2 Romex 15 A Lighting Circuits
12-2 Romex 20 A Lighting and Outlet Circuits, refrigerator
10-2 Romex 30 A Electric water heater, baseboard heaters
10-3 Romex 30 A Electric Clothes Dryer
What is the difference between 12 2 and 12 3 wire?
The designation 12/2 indicates AWG 12 wire with two conductors (AC hot and AC neutral), 12/3 indicates AWG 12 wire with three conductors (two AC hot and AC neutral). … AWG 12/2 is used for a single breaker 120V 20A max circuits. AWG 12/3 is used for double breaker 240V 20A max circuits.
How long can you run 14 gauge wire?
14 AWG 50 feet
—— ——-
10 AWG 64 feet
8 AWG 76 feet
6 AWG 94 feet
What is the difference between 10 2 wire and 10 3 wire?
For your welder what you want is 10-2 with a ground. The 10-3 is mainly used for household ranges that have 4 prongs on the plug it also has a ground wire.
Don’t forget to share this post 
References and Further Readings :
