Yes through the studs is fine. It’ll be safer enclosed in the wall than it was exposed on the floor. Depending on the route available to you or might be easier to use corrugated stainless steel vs black iron. Easier to feed through holes in the studs.
FYI: Gas lines can indeed be run in the attic. Also, you don’t have to run gas lines through the slab.
Thereof, Can you drywall over a gas line?
There is no minimum distance between the drywall and the gas line. I would install the above mentioned protection over any gas line that comes within 4″ of any nailer just to be safe. You could put a nail or screw into this line very easily and it may not leak right away.
Also to know is, Can you tap into an existing gas line? Can You Tap Into An Existing Gas Line? The answer you might have been hoping for is yes; you can tap into an existing gas line. You will just need to make sure that the line’s size provides enough gas flow to send gas to multiple utilities.
Subsequently, question is, Can you put a gas pipe in a wall? Try to run vertical pipes in walls in ducts, with access if possible, never inside the cavity. If the wall is thick enough to provide proper cover the pipe can be run in a chase. If tube has to be installed in purpose-designed ducts, these must be sealed to prevent the passage of gas into the wall cavity.
Also, Can you extend a gas line?
Gas Line Extension Cost If you have a gas line already in your home and are installing a new small appliance that runs on gas, you may extend an existing line. This is a smaller project than a new line, and because the smaller appliances require less gas, the size of the pipe can be smaller and less costly.
Can you run a gas line in a wall?
Try to run vertical pipes in walls in ducts, with access if possible, never inside the cavity. If the wall is thick enough to provide proper cover the pipe can be run in a chase. If tube has to be installed in purpose-designed ducts, these must be sealed to prevent the passage of gas into the wall cavity.
How do you protect exposed gas pipes?
For protection from housework and gardening and to keep gas meters near driveways and sidewalks from being hit, place two heavy metal pipes in concrete (much like you would set a fencepost) in front of and on both sides of the gas meter.
Where do gas lines run in house?
Supply, branch and drop lines or risers The piping inside the house is called the gas supply line or building line. Branch lines run to individual appliances. The branch line terminates in a drop line, which is a vertical pipe dropping down to the appliance from an overhead branch line.
How much does it cost to extend a gas line?
To run a new gas line, it’ll cost an average of $535. However, it can range anywhere from $120 to $1,350. Most homeowners spend between $259 and $815. Budget $15 to $25 per linear foot for new and replacement lines, including the labor, piping and materials.
Can a homeowner install a gas line?
Yes in most jurisdictions you can. It’s a very good DIY project and it can be done very safely. First you need to obtain the proper permit.
Does a gas pipe need to be sleeved through a wall?
Secondly, does a gas pipe need to be sleeved through a wall? Always sleeve the pipe where it passes through solid walls or floors.
Can you run flexible gas line in a wall?
CSST can run through walls, just like black pipe.
Can you cover gas pipes?
Additionally, can you cover gas pipes? Gas pipes must be protected and tested before covering. Protection can be provided by covering with PVC sleeving. Gas pipes must be accessable for inspection if compression fittings are used to join them.
Can you box in a gas pipe?
Yes you can box gas pipes in you can also paint! As for boxing them in you could use plastic C-section with brackets for fixing and corner pieces or box in with ply as long as it is screwed for easy access!Jul 19, 2018
How much does it cost to run a gas line from the street to the house?
Installing a natural gas line from the street to your house costs between $0 and $2,000, with most homeowners spending $980 for an average of 49 linear feet of connected pipe. The average cost is $12 to $25 per linear foot, while some gas companies offer free installation depending on the distance.
How do I protect my outside gas pipes?
How much does it cost to connect gas to house?
Area Cost to Install
————————— ———————
Run line from main to house $0 – $60/linear foot
Hook up to main $0 – $400
Install meter $0 – $600
Run lines in house $15 – $25/linear foot
Don’t forget to share this post 
References and Further Readings :