You can apply RedGard to concrete, cement backerboard, exterior grade plywood and exterior decks. It also bonds directly to metal and plastic drain assemblies. RedGard is tough enough to be used as a shower pan liner.
Cement is actually a very porous material and can easily absorb water. Therefore, any concrete that may come into regular contact with water, such as under tile or for a pool, will need to be waterproofed. If cement is not waterproofed, it can cause issues with the mortar used between the tiles.
Thereof, How do you waterproof a concrete floor before tiling?
For that reason, it is best to use an elastomeric, crack-prevention membrane to both seal the floor and protect your tile installation from failure. These membranes prevent water from seeping up through the concrete and into the mortar as well allowing the thinset to cure and preventing future mold or mildew growth.
Also to know is, Can you lay tile on sealed concrete? Attaching any tile product to sealed concrete is strongly advised against without first removing the sealer. The unmodified thinset would be the recommendation for use ON TOP of the DITRA when porcelain tile was used. DITRA is in fact a crack membrane but really isn’t intended to SOLVE any moisture problems.
Subsequently, question is, Should I redguard bathroom floor? You dont necessarily need it on the bathroom floor but any shower ( wall/floors ) or tub surround must be waterproofed.
Also, Do I need to prime concrete floor before tiling?
Priming New Concrete Floors While adhesive manufacturers say you can tile straight onto new concrete or screed, we would strongly recommend the use of a primer to ensure there is a good “key” for the adhesive to take to. … Eventually, this can lead to delamination where the tiles simply peel up!May 26, 2020
Will Thinset stick to RedGard?
Mike. You”ll be fine with thinset over Redguard on walls. It’s recommended for waterproofing niches, shelves, and entire shower walls when tar paper or poly are not used as a vapor barrier behind the CBU.
Does 100% silicone stick to RedGard?
Caulk that gap with siliconized or latex caulk and then use Redgard over the caulk. Regard will not stick to 100% silicone caulk. You DO NOT want moisture collecting in that crevice and it can if you stuff it with thinset.
Can you put RedGard over Greenboard?
Mike Girard MR drywall (“moisture resistant-green board) is absolutely not suitable for active wet locations and topical waterproofing membranes, such as Redguard, will not adhere properly to drywall. Tear it down and start over using cementious backer board.
How long do you let Thinset dry before applying RedGard?
This took about 1 to 1.5 hours. Drying time depends mostly on temperature & humidity levels and the surface will appear pink until the the RedGard has completely dried.
Does waterproofing membrane stick to silicone?
No, membrane and most things will not stick to silicon.
How do you waterproof a concrete floor?
Step 1 – Remove any paints, sealers, tile adhesive, efflorescence, and oils from the concrete. Step 2 – Shop-vac the surface of the concrete removing loose or crumbling concrete, mortar, dust, and dirt. Step 3 – Seal the concrete walls and floor against moisture and water vapor with RadonSeal Concrete Sealer.
How do you tile over a concrete slab?
More than almost any other type of floor covering, tile needs a rock-solid base. If you attach the tile to concrete, you need to take special precautions by uncoupling the tile from the concrete. Rather than using cement boards (CBUs), the favored method is to use an uncoupling membrane.
Will RedGard adhere to silicone?
When dry, apply an additional coat of the membrane. NOTE: Apply membrane over Silicone Caulk within 3 hours. Membrane will not adhere to silicone when applied on next day. … Use a rapid curing urethane caulk around the flange where the membrane and the upper flange make contact.
Do you need to use RedGard over cement board?
As long as it’s Cement Board & not some crappy “almost” cement board stuff. You really don’t need the RedGard, but the more protection the better…so go for it. And yes, you can do the boards beforehand. But, hit the filled seams & screws (your weak points) as soon as a panel is ready to give it some time to setup.
Can RedGard be used over drywall?
It’s true that RedGard can be used on drywall, but when all their product information is carefully considered, it is not the case that RedGard can be used on Drywall in a wet area.
Will adhesive stick to RedGard?
I know thinset will stick to Redgard, but the mechanism is different than with an adhesive – the cement grows interlocking crystals into the flexible material as it cures, an adhesive won’t.
What type of thinset should be used with Redgard?
Flexbond
Don’t forget to share this post 
References and Further Readings :
