Instead, select a 10- to 12-tpi blade for larger, gradual curves, or a 20-tpi blade for tight curves (1″ radius or less) in solid wood and all cuts in plywood or melamine-coated particleboard. … Finally, remember that jigsaw blades cost a fraction of the material you’re cutting.
To do this you need either a table saw or circular saw (as required by your needs, or available). The recommended blade for cutting the finished board products is the Bosch 10″ 80 tooth carbide blade or with a hand-held circular saw, a 100 tooth 5-1/2″ blade (iffy as results will show, but may be good enough).
Thereof, What is the best blade for cutting?
Framing blades have 24 teeth and are effective for jobs like rough carpentry where speed is more important than getting a clean cut. Plywood blades have 100 or more fine teeth designed to create a finish with minimal splintering. Thin-kerf blades have a narrow profile for faster, easier cutting and less material waste.
Also to know is, Can you cut melamine with a hand saw? Is using a hand saw for this project advisable? Yup, even with a power saw, masking the cut line with tape (and cutting through the tape) is the way to go. For melamine, plywood, and anything else made of compressed or brittle materials.
Subsequently, question is, Do you need a special blade to cut melamine? Since melamine is a plastic resin, it’s prone to chip and splinter. Luckily, there are a few easy tricks to get perfectly clean, factory-like edges. … Second, set your table saw or circular saw blade to cut about 1/4″ into one surface of the melamine.
Also, Will Home Depot cut melamine for you?
Re: cutting melamine? Yes, someone at Home Depot will cut it to your specs! … Your local Home Depot store that has an operating panel saw should be able to cut the plywood down in the size you requested, but the store will charge you for additional cuts after 2 of them.
Can you cut laminate with a hand saw?
You can perfectly well saw your laminate floorboards with a regular hand saw. … Always use a fine tooth and have the saw rolling before you touch the boards. Professional tip: test the direction of the teeth on your saw blade.
Can laminate be cut?
In fact, you can cut the planks using a table saw, miter saw, circular saw, hand saw or laminate cutter. However, using a diamond blade is recommended as laminate can be tough to cut through and may damage another type of blade. Typically, you will cut with the finished side up.
How do you cut a melamine board by hand?
– Clamp something (I used a known straight board) where the cut will go. …
– Use a sharp knife to score the cut. …
– Unclamp the board.
– Follow the score with a wide chisel (I used the widest I have) all the way over making the score deeper.
– Use the chisel again to chip out a grove about 1mm wide (or the width of your saw kerf.
How can I cut laminate without chipping?
If you’re forced to cut a laminate sheet from the front with a power saw, you can avoid chipping by laying masking tape along the cutline, sawing through the tape, and removing it after you’re done. You can further minimize chipping by using a plywood-cutting blade with a large number of teeth.
What saw blade makes the smoothest cut?
Blades with densely packed teeth make the smoothest cuts.
How do you cut a whiteboard without chipping it?
How do I choose a saw blade?
How do you cut melamine by hand?
– Clamp something (I used a known straight board) where the cut will go. …
– Use a sharp knife to score the cut. …
– Unclamp the board.
– Follow the score with a wide chisel (I used the widest I have) all the way over making the score deeper.
– Use the chisel again to chip out a grove about 1mm wide (or the width of your saw kerf.
Can laminate countertops be cut?
Plastic laminate is surprisingly easy to cut. You can do it with a circular saw, a jigsaw, a router or even some hand tools.
How do you cut plastic with a circular saw?
What do you use to cut laminate?
You can use several tools to cut laminates, including a table saw or handheld power saw, a utility knife, a router or a hand slitter. The best cutting approach depends on whether you’re rough cutting or finishing edges.
How many teeth blade for ripping?
Ripping: 10-inch blades with 24-30 teeth and 12-inch blades with 40 or fewer teeth.
Don’t forget to share this post 
References and Further Readings :
