Polyurethane over epoxy is just fine.
Epoxy with two-part polyurethane varnish Two to three coats of epoxy also provide a stable base for clear two-part polyurethane finishes. Applied over epoxy, they perform beautifully together and outlast either coating used by itself.
Thereof, Can you put polyurethane over epoxy?
Epoxy with two-part polyurethane varnish Two to three coats of epoxy also provide a stable base for clear two-part polyurethane finishes. Applied over epoxy, they perform beautifully together and outlast either coating used by itself.
Also to know is, Is 2 coats of polyurethane enough? You are best off using 3 coats of water based polyurethane for the best results. … Not only is water borne polyurethane thinner, but it also raises the grain of the wood, so the floors can sometimes feel rough with just 2 coats of poly (especially if it’s a cheap brand of poly).
Subsequently, question is, How long should water based polyurethane dry between coats? 1-2 hours
Also, Can you apply polyurethane over?
Applying one or two coats of polyurethane to a painted surface is a good way to protect the paint. … Oil-based polyurethane levels out to a smoother finish, although it takes several hours longer to dry. You can apply polyurethane over any type of paint, as long as it’s clean and has been properly prepared.
Can you put a clear coat over epoxy?
Clear epoxy coatings are usually applied as an additional protection layer on top of an epoxy or polyurethane floor. They can serve several purposes such as scratch resistance, protecting flakes and other aggregates, as well as general protection from dirt pick up.
What happens if you don’t sand between coats of polyurethane?
Failing to sand between coats of polyurethane does not have a significant impact on the finish. Even so, I still advise that you sand between the coats when applying polyurethane as this will help increase the adhesion between the layers to give you a more level finish.
What do you do after the final coat of polyurethane?
– Sand the uneven finish using fine-grit sandpaper. Try not to sand too hard or you may go through into the stain, requiring that you re-stain the area.
– Wipe away dust and debris with a clean cloth.
– Apply a very light coat of polyurethane to the sanded area with a brush.
Can you put new epoxy over old epoxy?
Can I put another coat of epoxy over cured epoxy? Yes. Since the epoxy has cured a chemical bond is not possible so what is called a mechanical bond is needed. This simply means that the cured epoxy has to be lightly sanded before the next coat is applied: the first coat should have a matt, almost white, surface.
Can I put sealer over epoxy?
Step 1 – Wait 48 Hours after Applying Your Epoxy Floor Be sure your epoxy floor has dried and cured thoroughly before sealing it with a protective topcoat. This will enable you to identify any potential problems with moisture seepage or alkalinity before they happen.
Can you apply a second coat of polyurethane without sanding?
Apply two to three additional coats of full-strength polyurethane, sanding between each coat. When applying polyurethane, brush along the grain, stretching the polyurethane into as thin a coat as possible. Always allow polyurethane to dry 24 to 48 hours before sanding, to give the surface time to cure and harden.
When can I apply a second coat of epoxy?
Depending on the epoxy you’ve chosen to work with, you’ll have to wait between 4 and 24 hours before applying your second coat. Be sure to read your directions very thoroughly before beginning your project.
What can you put over epoxy?
Epoxy with two-part polyurethane varnish Two to three coats of epoxy also provide a stable base for clear two-part polyurethane finishes. Applied over epoxy, they perform beautifully together and outlast either coating used by itself.
How do you apply a second coat of epoxy?
1) First, you can wait 24 hrs after your first pour, sand down the whole piece with coarse sandpaper to create some tooth, and pour your second coat at that point, as originally described. Repeat until you reach the thickness you desire.
Can I put polyurethane over epoxy?
Epoxy with two-part polyurethane varnish Two to three coats of epoxy also provide a stable base for clear two-part polyurethane finishes. Applied over epoxy, they perform beautifully together and outlast either coating used by itself.
Should you sand between coats of water based polyurethane?
With water-based topcoats, sand any “grain-raise” smooth before applying the final coat. Note: Sanding between coats is not necessary, but it will provide a better finish. After a coat has dried, use 220 or 240 grit sandpaper or extra fine steel wool to lightly sand surface.
Can you recoat rustoleum epoxy shield?
Can I recoat EpoxyShield? … Only one coat of EpoxyShield is needed on most concrete floors. If a second coat is needed / desired, it can be applied once the initial coat has dried. For the best adhesion, apply the second coat within 4 days of the first coat.
Don’t forget to share this post 
References and Further Readings :
