These surrounds are made of acrylic, and the panels are attached to the walls with special adhesives. If you are installing a tub surround and you need to cut holes for the faucet and spout or trim it to fit the space around your tub, make sure you cut it carefully to avoid chipping or damaging the tub surround.
Thereof, Do you put drywall behind a shower surround?
Fiberglass and acrylic tub and shower enclosures come with a flanged edge that attaches directly to the wall studs, and the proper way to hide this flange is to install drywall over it. Consequently, enclosures are typically installed on the bare studs.
Also to know is, How do you cut shower wall panels?
Subsequently, question is, What do you put behind a shower surround? Install cement board or an equivalent moisture-resistant backing material on walls behind tub and shower enclosures composed of tile or panel assemblies with caulked joints. Don’t use paper-faced backer board, i.e., paper-faced drywall, behind seamed tub and shower enclosures.
Also, Can you install shower surround over drywall?
The short answer to the question is, “It’s not recommended.” However, this answer only really only suffices if you’re converting a room that was never a bathroom into a wet space. Drywall on its own is not suitable for use in bathrooms because it is prone to absorbing moisture and thus losing structural integrity.
How do you trim a shower surround?
How do you install a shower surround to studs?
– Prepare the Walls. Unless the studs are already exposed, installation starts by stripping the walls down to the studs around where the surround will sit. …
– Install the Back Wall Panel. …
– Install the Side Wall Panel(s) …
– Prepare the Front Wall Panel. …
– Install the Front Wall Panel. …
– Complete the Installation.
What is the best way to cut fiberglass tub?
The easiest way to get a fiberglass tub out of the bathroom is to cut it into small sections, which can be done using a jig saw with a fiberglass blade. You can find saws and saw blades at your local hardware store.
What type of drywall goes behind a shower?
Install cement board or an equivalent moisture-resistant backing material on walls behind tub and shower enclosures composed of tile or panel assemblies with caulked joints. Don’t use paper-faced backer board, i.e., paper-faced drywall, behind seamed tub and shower enclosures.
What goes behind shower walls?
Rigid air barrier materials for use behind showers and tubs include fiber-cement, fiber-reinforced gypsum, glass mat gypsum, or fiber mat-reinforced cementitous backer panels.
How do you cut shower panels?
What is the best adhesive for shower surround?
Loctite PL 550 Tub Surround Adhesive
How do you install shower wall panels?
How do you finish the outside edge of a tile shower?
To give the edge a clean, water-tight finish, place a piece of masking tape one grout joint away from the edge of the last tile. Fill this gap between the tile and the masking tape with a smooth bead of caulk. This will finish the edge without extra tiles.
Which is better for a tub acrylic or fiberglass?
Acrylic is much more durable than a fiberglass tub. The chance of an acrylic tub chipping, cracking or fading is unlikely. Fiberglass tubs can fade and get cracked and scratched over time. Both styles can be cleaned with simple cleaning solutions.
How do you glue a shower surround?
– Apply the adhesive to the back wall as described earlier, and then spread it around with the trowel.
– Take the panel, line up along the wall markings and press it onto the wall. …
– Repress it firmly against the wall to make it adhere properly.
Do you put insulation behind shower walls?
The insulation behind the tub or shower should be equivalent to the insulation in the rest of the exterior walls and should be covered with an air barrier of cement backer board, rigid foam insulation, or non-paper-faced drywall that is sealed at the edges and seams to provide a continuous air seal.
Don’t forget to share this post 
References and Further Readings :
