The fascia can be nailed directly to the truss tails, but while the sub-fascia is typically a 2x, t…
The fascia board on the Gable end of a home is called a “barge rafter”. Often these rafters extend past the eaves to create a place to hide the end of the gutter or as a decorative element.
Thereof, Are fascia boards necessary?
Fascia boards are essential to your home. They provide a solid foundation for your gutters and help keep pests out. With some homes, they also work in conjunction with soffits providing essential ventilation for your attic. They also make the exterior of your home look finished.
Also to know is, How far should Roof sheathing overhang rafter tails? Measure up the rafter 45-3/4 inch from the cut end of the truss tail and snap a line along the trusses. This indicates the upper edge of the first row of roof sheathing—leaving enough overhang that the subfascia and fascia will tuck neatly underneath when the time comes.
Subsequently, question is, Do you need a fascia? Fascia boards are necessary for a gutter system to be installed, which is important to keep rain moving off your roof and away from your siding and foundation. A soffit and fascia are paired together, and the fascia board is where the roof and the outer walls meet.
Also, Is fascia board necessary?
Fascia boards are necessary for a gutter system to be installed, which is important to keep rain moving off your roof and away from your siding and foundation. A soffit and fascia are paired together, and the fascia board is where the roof and the outer walls meet.
Should roof sheathing be flushed with fascia?
When sheathing a roof, the first step is to snap a line so that the first row goes on straight. But if you snap it at 40 inches, then the sheathing will not project over the subfascia or true fascia. This opens the door to the possibility of water damage by letting gravity work against you. Don’t do that.
What is the purpose of a fascia board?
The fascia board is the long, straight board that runs along the lower edge of the roof. The fascia is fixed directly to the lower ends of the roof trusses and usually does all the work of supporting the lower edge of the bottom row of tiles. The fascia board also carries all the guttering.
How far should Roof sheathing overhang fascia?
How do you make a gable overhang?
When should I replace my fascia?
Tell tale signs There are a number of signs and symptoms that it’s time for new fascia and soffits: Soft patches in wood, which means rot or holes are appearing. Crackled, flaking paint, which is a general sign of age.
What is the purpose of fascia board?
The fascia board is the long, straight board that runs along the lower edge of the roof. The fascia is fixed directly to the lower ends of the roof trusses and usually does all the work of supporting the lower edge of the bottom row of tiles. The fascia board also carries all the guttering.
How far should shingles overhang the roof?
Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.
Can drip edge be installed after shingles?
The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.
What is a barge rafter in construction?
The fascia board on the Gable end of a home is called a “barge rafter”. Often these rafters extend past the eaves to create a place to hide the end of the gutter or as a decorative element.
How far should sheathing overhang fascia?
The overhang is multiple meaning that the sheeting you would overhang some 3/4-1″ followed by a drip edge then if using shingles another 1″. If using metal w/o drip another 3/4-1″ past the wood sheeting. You would want to keep your completed overhang close to 1-1/2″ if using gutter.
Does sheathing go over fascia?
When sheathing a roof, the first step is to snap a line so that the first row goes on straight. But if you snap it at 40 inches, then the sheathing will not project over the subfascia or true fascia. … Add an inch and a half for subfascia, strike a line.
What is a valley rafter?
: the rafter running from the wall plate to the ridge and along the valley of a valley roof.
Don’t forget to share this post 
References and Further Readings :