1/4″
Type Gauge Size
—————- ————————————————
Slot or Flathead 1/8”, 5/32”, 3/16”, ¼”, 5/16”, ⅜”
Phillips #000, #00, #0, #1, #2, #3,
Allen or Hex 0.7, 0.9, 1.3, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5 mm
Torx T2, T3, T4, T5, T10, T15, T20, T25, T30, T40
Thereof, What size is a #0 screwdriver?
Phillips # Tip Width (Metric) Fits Screw Sizes
———- —————— —————-
#0000 1 mm
#000 1.5 mm
#00 2 mm
#0 2.5 mm 0-1
Also to know is, What size is a #1 screwdriver? Screw Gauge Point Size
———– —————- ——-
Slot or Flathead Philips
2 ⅛” / 3.2mm #1
3 5/32” / 4.0mm #1
4 3/16” / 4.8mm #1
Subsequently, question is, What size is a #1 Phillips screwdriver? Screw Gauge Point Size
———– —————- ——-
Slot or Flathead Philips
2 ⅛” / 3.2mm #1
3 5/32” / 4.0mm #1
4 3/16” / 4.8mm #1
Also, What size is a #2 Phillips screwdriver?
1/4″
What is the difference between ph1 and ph2?
This preview shows page 1 – 2 out of 2 pages. The numerical difference between pH=1 and pH=2 is one, while the chemical difference is that at pH=1, the [H+] is 10-1, which is ten times higher than the [H+] at pH=2, which is 10-2.
How are slotted screwdrivers measured?
In a set, you will get a good selection of drivers including at least one with a short shaft, one with a long shaft, and several in between. Standard slotted screwdrivers are measured in inches and fractions of inches.
How big is a #2 Phillips?
1/4″
What is the most common Phillips screwdriver size?
While screw size is shrouded in mystery, there are four basic sizes of Phillips screwdriver — from #0 to #4 — #0 being the smallest. The most common sizes are #2 and #1, #2 for standard screw sizes, #1 for “miniature”.
How do you know what size screwdriver to use?
Look along the table to find out the screw’s number and the size of screwdriver bit needed to insert or remove it. For example, if you had a pozidriv screw with a shank diameter of 3.0 mm, you can see from the table that it’s a number 4 screw and needs a PZ1 screwdriver bit to insert or remove it.
What do screwdriver numbers mean?
While screw size is shrouded in mystery, there are four basic sizes of Phillips screwdriver — from #0 to #4 — #0 being the smallest. The most common sizes are #2 and #1, #2 for standard screw sizes, #1 for “miniature”. Then there are the jeweler-size screws.
What is the smallest screwdriver size?
The most important technique is to use the right size screwdriver. While screw size is shrouded in mystery, there are four basic sizes of Phillips screwdriver — from #0 to #4 — #0 being the smallest. The most common sizes are #2 and #1, #2 for standard screw sizes, #1 for “miniature”.
What is a #1 Phillips screwdriver?
A #1 Phillips Screwdriver means that the Phillips tip will fit into the equivalent (or in this case #1) screw head.
What can I use instead of a small screwdriver?
If you’re dealing with a single-slot screw, head to your kitchen or wallet for an alternative to a screwdriver. The first thing you could try is a kitchen knife. Choose one that has a rounded tip like a butter knife or a small knife that you would use for a cheese board.
What is the standard Phillips screwdriver size?
While screw size is shrouded in mystery, there are four basic sizes of Phillips screwdriver — from #0 to #4 — #0 being the smallest. The most common sizes are #2 and #1, #2 for standard screw sizes, #1 for “miniature”.
What is the difference between a 1 and a 2 Phillips screwdriver?
Phillips head screwdrivers are built to work with the same screws, only those with crossheads instead. … The #0 Phillips head drivers fits screw numbers 0 and 1 while the #1 Phillips head fits screw numbers 2, 3, and 4. #2 Phillips head screwdrivers fit screw numbers 5, 6, 7, 8, and 9.
How many different sizes of Robertson screws are there?
five different
Don’t forget to share this post 
References and Further Readings :
